Kenmore Dishwasher 665.15974992 (66515974992, 665 15974992) Parts

This replacement wheel restores smooth movement for the appliance's moving assembly, helping reduce noise and prevent binding for consistent operation. Ideal when worn or damaged wheels cause dragging or uneven motion. What it does:

• Supports and guides a rotating or sliding component to maintain smooth movement
• Reduces friction and prevents binding that can cause rubbing or grinding noises
• Helps stabilize moving parts to eliminate wobble and uneven operation
• Restores proper alignment so the assembly runs quietly and reliably

• Disconnect power to the appliance before starting any repair
• Inspect surrounding mounts and clips for damage; replace if worn
• Use basic hand tools; avoid forcing parts to prevent damage

This wheel leg is a replacement support used to stabilize and allow smooth movement of the appliance's lower assembly. It restores proper leveling and reduces wobble so the appliance sits securely and rolls or rests as designed. What it does

• Supports the appliance chassis at the lower corner and transfers load to the floor
• Helps maintain correct appliance height and leveling to reduce vibration and rocking
• Restores proper rolling or stationary support where a worn or broken leg caused instability
• Commonly replaced when the leg is cracked, stripped, missing, or no longer holds weight

• Verify appliance is unplugged and empty before accessing lower cabinet or base
• Support the appliance with a block or jack to prevent shifting while replacing the leg
• Remove any access panels or retaining hardware as needed; install the new leg in the original orientation
• Replace any fasteners that are damaged and test stability before returning the appliance to service

Notes: Only one screw hole is used now.

Note: There are four wheel assemblies includes with this rack. The flexible tine rows are not included. This is a lower dishrack assembly for a dishwasher. This part holds the dishes during the washing and drying cycles. Note that this is only the lower dishrack assembly and the upper dishrack assembly is sold separately. Over time, the lower dishrack assembly may begin to rust or the coating may wear off. It is also possible that sections of the part could break due to degradation over time. If this happens, the entire lower dishrack assembly will need to be replaced. The lower dishrack assembly is compatible with dishwashers that are manufactured by the Kenmore, KitchenAid, and Whirlpool brands. It comes straight from the manufacturer and is sold individually. It's a genuine, high-quality, and durable OEM part.

This inlet base seal is a gasket that fits between the inlet base and its mating surface. Replacing a worn seal helps maintain proper airflow through the inlet path and keeps spills and debris out of internal components.

• Forms a tight, continuous seal at the inlet base-to-housing joint
• Helps preserve correct airflow through the inlet path
• Blocks liquids, grease, and crumbs from leaking into the appliance interior
• Replace if the seal is cracked, flattened, brittle, loose, or you see visible gaps

• Disconnect power to the appliance before servicing
• Remove grates/cartridges, filters, or trim as needed to access the inlet base
• Clean and dry mating surfaces; install the new seal in the same orientation without stretching or twisting
• Reassemble and verify the seal sits evenly with no gaps

This push retainer is a small press-on fastener that secures components to shafts or studs inside your appliance. It restores a tight, reliable hold so knobs, trim, or linkages don't loosen or fall off during use. What it does:

• Presses onto a shaft or stud to secure knobs, trim, or linkages—no threads required
• Maintains spring tension to resist vibration during normal operation
• Replaces a missing, bent, or weakened retainer
• Common symptoms: loose or wobbly knobs/trim, parts slipping off, or a retainer that won't stay on

• 1 push retainer

• Disconnect power; for gas appliances, also shut off the gas supply
• Access the shaft/stud and carefully remove the old retainer with pliers; avoid damaging adjacent plastic parts
• Press the new retainer on squarely using a deep socket or nut driver; do not hammer directly
• If the mating shaft or component is damaged or deformed, address that before installing the new retainer

Screw for wash impeller.

This overfill control switch (float switch) senses water level and helps stop the fill valve to prevent overfilling. It replaces a worn or failed water-level safety switch to restore proper fill control and reduce overflow risk. What it does:

• Detects high water level and signals the washer control to stop filling
• Helps prevent water overflow and unintended flooding when working correctly
• Commonly linked to symptoms like continuous filling, overfilling, or washer not advancing cycles
• Interfaces with the washer control board and fill valve to maintain proper water level

• One overfill control switch (float switch)

• Disconnect power and turn off water supply before starting any repair
• Handle connectors gently; confirm wiring positions or take a photo before disconnecting
• Verify proper operation after installation by running a short fill cycle and checking for correct shutoff