Kenmore Range 790.60702900 (79060702900, 790 60702900) Parts

This handle mounting screw secures an appliance handle, most commonly the oven door handle, to the door or front panel. Replacing a worn, stripped, or missing screw restores a firm grip and keeps the handle aligned and secure.

• Secures the handle to the door or trim as designed
• Replaces stripped, rusted, or missing hardware
• Helps correct a loose or wobbly handle
• Reduces rattling or misaligned trim caused by a missing fastener

• Disconnect power; for gas appliances, also shut off the gas supply
• Support the handle and door/front panel during removal and installation
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten until snug—do not overtighten

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

This oven insulation surrounds the oven cavity to retain heat and protect nearby components and cabinetry. Replacing a burnt or deteriorated insulation blanket restores temperature stability and helps keep exterior surfaces cooler on your range during cooking.

• Minimizes heat loss for more consistent baking temperatures
• Shields wiring, controls, and adjacent cabinets from excessive heat
• Damaged insulation can cause long preheat times or trouble maintaining set temperature
• Exterior panels or control area may feel unusually hot, or a burnt odor may persist after spills

• Disconnect power at the breaker; shut off gas
• Allow the appliance to cool completely before service
• Access typically requires pulling the range and removing outer panels; note original routing and retainers for reassembly
• Handle insulation carefully; wear gloves, eye protection, and a dust mask to avoid irritation from fibers

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation

This is a burner control switch for a stove. This part controls the temperature of the heating element on a stove cooktop or range. When the user turns the knob to increase the heat that is produced on the burner, it activates the burner control switch.A new burner control switch may be needed if the user is unable to control the heat on the stove. The burner may get hot and then it may not turn off. The burner may only work when it's on high heat. Alternately, the burner may not heat at all. Never perform care and maintenance on an appliance that is powered on.This is a genuine Frigidaire part and is sourced directly from the manufacturer. It is sold individually. This specific burner control switch is compatible with stove cooktops and ranges that are manufactured by Frigidaire, Kenmore, Crosley, and Westinghouse.

250V.

This temperature-activated limit thermostat is a safety switch for the range/wall oven that reacts to excessive heat to protect internal wiring and controls. Replacing a failed thermostat can restore reliable heating and reduce nuisance shutdowns during baking or self-clean.

• Monitors oven/cabinet temperature and switches its circuit at a calibrated threshold to protect components
• Failure symptoms can include: no bake or broil heat, oven shutting off mid-cycle, or loss of heat after a self-clean cycle
• On some models, a failed thermostat may also affect the cooling fan (not running or running unexpectedly)
• Can be checked with a continuity test per your model's tech sheet

• Disconnect power at the breaker and let the appliance cool completely before service
• Location varies by model; commonly mounted to the rear of the oven cavity, upper plenum, or behind the back panel
• Photograph wiring and transfer leads one at a time; reuse original mounting hardware/orientation
• Never bypass a safety thermostat; replace only with the specified part number

Size: 8-32t x 0.500 inch. Color: Black.

Support for broil heating element.

This is the variable control switch for an electric range's cooktop burner. It regulates power to the surface element so you can select steady, repeatable heat levels and restore reliable on/off control. What it does:

• Regulates voltage to a surface element based on knob position (low through high)
• Typical failure symptoms: burner won't heat, only heats on high, won't shut off, or heats inconsistently
• Can address issues when the control shaft is damaged or the switch shows signs of overheating at the terminals

• 1 switch

• Disconnect power before servicing
• Access the control panel/console to reach the switch
• Note wire locations and transfer them to the new switch one at a time
• Secure the switch in the panel, reinstall knob, and test burner operation before reassembly

This replacement clip secures components within your appliance. Replacing a broken, bent, or missing clip restores a firm hold on panels or assemblies to prevent shifting and reduce vibration noise.

• Holds specified parts or panels in place where a clip is called out in the assembly
• Helps maintain proper alignment and minimizes rattles/vibration
• Direct replacement for a damaged or missing clip
• Common symptoms: loose or misaligned parts, rattling during operation, clip visibly broken or missing

• Disconnect power before service; also shut off gas/water supplies
• Note the original clip orientation and placement; take a photo for reference
• Use needle-nose pliers for removal/installation; avoid overbending or deforming the clip
• Inspect mating parts for wear or damage and ensure the clip seats fully

Size: 6-20 x 0.312 inch.

A small replacement retainer clip that secures trim, panels or components in place to restore proper alignment and stop rattles or loosening. Fits original mounting points for a factory-style repair. What it does:

• Secures refrigerator trim, panels or small components to prevent movement and noise
• Keeps parts aligned so doors and drawers fit and operate smoothly
• Helps maintain grille, kickplate or interior trim attachment where clips are used
• Simple, non-electrical part — no wiring or calibration required

• Basic hand tools usually required; access the clip location before removal
• Remove any panels gently to avoid damaging surrounding trim or fasteners
• Replace only the worn or broken clip; align part fully before snapping into place
• Disconnect power to appliances with electrical components before starting work

This factory screw secures components in your appliance, restoring a tight, rattle-free fit. Replace missing or damaged hardware to keep panels, brackets, and trim properly fastened and aligned for safe, reliable operation.

• Secures panels, brackets, trim, or internal components to the chassis
• Replaces lost, rusty, stripped, or cross-threaded screws
• Helps eliminate looseness, gaps, and vibration/rattling
• Common signs: loose/misaligned panels or trim, rattling noises, missing or rounded screw heads

• Disconnect power (and shut off gas if applicable); allow the unit to cool completely
• Match to the original location and replace one at a time to maintain alignment
• Hand-start to prevent cross-threading; tighten snugly—do not overtighten
• Use light torque when threading into plastic or thin sheet metal

A decorative medallion trim piece that restores the finished look of your appliance front. Replaces a scratched, faded or missing medallion to improve appearance and maintain original styling. What it does:

• Covers and protects the underlying surface while matching the appliance's original finish
• Restores a clean, finished look when the factory medallion is damaged or discolored
• Helps keep grime and moisture out of seams around the emblem area
• Useful when replacing a damaged control/door trim for a consistent appearance

• One medallion decorative trim

• Surface-mount replacement; peel adhesive or fasten per original attachment method
• Clean and dry mounting area before installing for best adhesion
• Handle carefully to avoid scratching the finish during installation

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit