Kenmore Range 790.75602100 (79075602100, 790 75602100) Parts

Complete igniter and orifice assembly for gas range burners. Includes igniter, orifice holder, and gas tube. Replace if cracked, broken, or damaged.

This vent grille is mounted on the range or oven and covers the ventilation opening that allows hot air and steam to escape during cooking. It helps direct airflow away from the appliance while keeping debris out of the vent duct. Replace this grille if it is cracked, warped from heat exposure, discolored, or if the vent louvers are broken and no longer directing airflow properly.

This rocker switch is the on/off control used in the appliance's control panel. It opens and closes the circuit to a selected feature, restoring dependable operation when the original switch becomes worn, stuck, or fails.

• Controls a single on/off circuit from the control panel
• Restores proper switching for the associated feature
• Common symptoms: feature won't turn on or off, light or function flickers or stays on, switch feels loose or sticks
• Replaces a cracked, burned, or unresponsive rocker

• Disconnect power at the breaker before servicing
• Access the switch from the control panel or mounting area; note/photograph wire positions
• Move wires to the new switch one at a time and seat the switch securely in the panel opening
• Restore power and test operation before reassembly

Replacement power cord for ovens and ranges. Installs at the rear panel to restore electrical connection. Needed when original cord is frayed or damaged.

For 12k burner.

Oven won't light even though igniter glows? Burner lights only when valve is tapped? Replace the dual gas safety valve. DIY install in under 1 hour.

Secures the glass light cover to your range oven cavity. Replace if the retainer is cracked, broken, or missing to keep the lens firmly in place.

This metal rack fits inside the warming drawer beneath the oven, providing a flat surface to hold plates, dishes, or cooked food at a warm serving temperature. It slides in and out of the drawer on built-in guides. Replace it if the rack is bent, warped, rusted, or missing, which can prevent proper food placement and even heat distribution in the warming drawer.

Body-side spacer for gas range door or lid hardware. Installs on cabinet side to set correct stand-off and alignment. Replace if cracked or missing.

Black burner grate for gas range cooktops. Replace your cracked, chipped, or missing grate to restore proper support for pots and pans during cooking.

A replacement hex-head screw used to secure appliance regulator brackets and similar small components. Restores proper fastener fit so panels and brackets stay firmly attached. What it does

• Fastens regulator bracket and related sheet-metal components
• Provides a secure threaded connection for components where an 8-18 thread is specified
• Helps eliminate looseness or rattling caused by a missing or damaged screw
• Matches the nickel/chrome finish commonly used on interior mounting locations

• One hex head screw (8-18 x 3/8), nickel finish

• Intended for use where an 8-18 x 3/8 hex screw is specified by the manufacturer
• Tighten to snug; avoid over-torquing which can strip sheet-metal threads
• Turn off power to the appliance before accessing internal components
• If the original screw used a lock washer or threadlocker, replace or reapply as appropriate

This is a metal cover that fits over the convection fan assembly in the back wall of the oven cavity. It protects the fan and heating element while allowing hot air to circulate evenly during convection cooking. Replace this cover if it is warped, cracked, or corroded, which can cause uneven heating or rattling noises during convection baking.

Range indicator light lens kit with red and clear lenses. Replace when cracked, discolored, or missing. Fits control panel burner indicators. Verify fit.

Guide pin for gas ranges. Secures and aligns oven or burner components. Replace if broken, missing, or worn to restore proper part positioning.

Valve mounting screw for cooktop burner assembly. Secures gas valve to mounting bracket. Replace if stripped, missing, or corroded during repairs.