Kenmore Range 790.95300100 (79095300100, 790 95300100) Parts

The Anti-Tip Bracket Kit is an OEM part for Frigidaire ranges and ovens. This part secures the appliance to the floor or wall, preventing it from tipping over when the oven door is opened or when heavy cookware is placed on an open door or extended rack. The kit typically includes a metal bracket, screws, and installation instructions.

Over time, or during instances of moving or remodeling, the anti-tip bracket may become dislodged or may not be reinstalled correctly, which can compromise the safety of the appliance. 

Symptoms of a missing or improperly installed Anti-Tip Bracket include:

• The range or oven tilts forward when pressure is applied to an open door
• The appliance moves more easily than expected when nudged or cleaned
• Visible absence of a bracket at the lower back portion or floor area behind the appliance

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This adhesive control panel overlay is the faceplate for the electronic oven control on select ranges and wall ovens. It restores readable button labels and a clean, protected surface when the original overlay is faded, bubbled, or damaged.

• Provides printed legends for the keypad buttons and display around the electronic control (EOC)
• Protects the touch surface from wear and cleaning
• Restores a neat, easy-to-read control area
• Typical replacement reasons: peeling, bubbling, cracks, discoloration, or illegible labels

• Disconnect power to the appliance before servicing the control panel
• Remove the control panel/bezel as required to access the old overlay
• Peel off the old overlay; clean and dry the mounting surface before applying the new one
• Align with display and key locations; press from center outward to bond and smooth out air

Color: White.

The Rocker Switch is an OEM part for Frigidaire ranges and ovens. It is responsible for turning the interior oven light on and off. The light switch allows visibility of the oven cavity for viewing food during the cooking process.

Causes can include normal wear and tear over time, exposure to heat inside the oven cavity, or accidental damage.

Symptoms of a bad oven light rocker switch include:

• The oven light failing to illuminate when the door is opened
• The light remaining on even when the door is closed
• An inconsistent or flickering oven light
• The switch itself becoming loose, cracked, or non-responsive

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This truss-head machine screw secures a switch to its mounting bracket or panel. Replacing a worn or missing screw restores a solid, aligned switch fit for reliable operation.

• Fastens the switch body to a bracket or chassis panel
• Helps keep the switch aligned for consistent actuation
• Replaces stripped, corroded, or missing mounting hardware
• Common symptoms: loose or wobbly switch, misalignment, rattling or vibration around the switch area

• Disconnect power to the appliance before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Verify thread size and length match the original hardware
• If multiple screws secure the switch, replace them in a consistent pattern to maintain alignment

Size: 3/4 inch od x 1/4 inch id.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

Color: White. For bisque order 316270202. This oven door handle no longer comes with an insert for the screw. Which means you will need to order the replacement screws part number 5304500008 to grip into the plastic of the new handle.

This oven door hinge supports and guides the door so it opens and closes smoothly and seals properly. Replacing a worn hinge can restore correct door alignment and help prevent heat loss from a door that won't close tightly.

• Supports the oven door and controls its opening/closing movement
• Helps maintain proper door alignment and seal for stable temperatures
• Replace if the door won't stay closed, sags, binds, or slams
• Symptoms can include heat escaping around the door, uneven baking, or creaking/grinding when moving the door

• Disconnect power at the breaker; allow the oven to cool completely
• Remove the door; use hinge locks/pins if the design provides them
• Install the hinge in the original orientation and mounting points; re-seat the door and verify latch engagement
• Check door alignment; replacing both hinges together can help ensure even closing force

Restore smooth, secure door movement with this oven door hinge. A worn hinge can cause the door to sag or leak heat; replacing it helps the door close flush for better heat retention and consistent baking performance. What it does:

• Provides spring-tensioned pivot for the oven door
• Helps keep the door aligned and fully closed against the gasket
• Common fixes: door won't close fully, drops quickly, won't stay ajar, squeaks or binds
• Reduces heat loss and temperature fluctuation caused by a misaligned door

• One door hinge assembly

• Disconnect power at the breaker and let the oven cool completely
• Support the door; engage hinge locks or remove fasteners, then lift the door off per your model's instructions
• Remove the faulty hinge and install the new hinge in the same orientation; reuse mounting hardware
• Open and close the door to verify smooth motion and a tight seal before use

250V.

This burner cap sits on top of the sealed burner head on a gas cooktop/range to evenly distribute flame and protect the burner from spills. Replacing a damaged or missing cap helps restore proper flame pattern and efficient cooking performance.

• Covers the burner head to shape the flame and shield it from debris
• Helps ensure even heating across cookware
• Common signs it may need replacement: uneven or yellow flames, sputtering or noisy burner, cookware scorching on one side, cap chipped, warped, or missing
• Color/finish: black

• Shut off gas supply and allow the cooktop to cool completely before servicing
• Lift off the old cap; clean the burner head surface
• Center the new cap on the burner head—ensure it seats flat and stable
• Test the burner for a steady, even blue flame after reassembly

This oven light lens retainer secures the glass light cover to the oven cavity so the bulb area stays protected during cooking. Replacing a damaged or missing retainer keeps the lens firmly in place and prevents nuisance loosening.

• Holds the glass light lens securely inside the oven cavity
• Helps shield the bulb area from splatters and debris
• Direct replacement for a bent, warped, or missing retainer ring
• Common symptoms: lens won't stay in, cover rattles, or difficulty securing the lens after service

• Disconnect power at the breaker and allow the oven to cool completely
• Remove oven racks for easier access to the light cover area
• Support the glass lens while positioning the retainer to avoid drops or chipping
• Secure the retainer per your model's design; do not overtighten

This outer glass door kit replaces a damaged or worn exterior oven/microwave door panel, restoring appearance and helping maintain proper heat containment. Designed as a direct-fit exterior glass assembly in black with pre-applied foil tape. What it does:

• Replaces cracked, chipped, scratched or cosmetically damaged outer door glass
• Restores the door's finished appearance and helps maintain the door seal integrity
• Works with the door assembly so heat and steam are properly managed during operation
• Helps eliminate drafts or light leakage caused by damaged outer glass

• Intended to be installed by a confident DIYer familiar with appliance disassembly
• Power off and unplug the appliance before starting; allow appliance to cool completely
• Take care handling glass; wear cut-resistant gloves and eye protection
• Follow OEM service instructions for door removal and reassembly to avoid damage

This body-side spacer installs on the cabinet side of the door or lid hardware. It sets the correct stand-off and alignment so the handle or latch feels solid and sits flush for a clean, secure fit. What it does:

• Positions and supports door/lid hardware on the cabinet/body side
• Maintains proper spacing to help prevent rubbing or scuffing of the panel
• Helps keep the handle or latch tight and aligned
• Common symptoms: loose or wobbly handle/latch, uneven alignment, visible gap or scuff marks at the mounting point

• Includes 1 body-side spacer

• Disconnect power to the appliance before servicing
• Support the handle/latch, remove the cabinet-side mounting screws, place the spacer, realign hardware, and reinstall screws snugly
• Reuse the original fasteners; avoid overtightening to prevent cracking the spacer or stripping threads
• Check door operation and alignment before finishing

Original Frigidaire Part.