Kenmore Range 790.95929301 (79095929301, 790 95929301) Parts

This metal rack fits inside the warming drawer beneath the oven, providing a flat surface to hold plates, dishes, or cooked food at a warm serving temperature. It slides in and out of the drawer on built-in guides. Replace it if the rack is bent, warped, rusted, or missing, which can prevent proper food placement and even heat distribution in the warming drawer.

Body-side spacer for gas range door or lid hardware. Installs on cabinet side to set correct stand-off and alignment. Replace if cracked or missing.

This is a metal cover that fits over the convection fan assembly in the back wall of the oven cavity. It protects the fan and heating element while allowing hot air to circulate evenly during convection cooking. Replace this cover if it is warped, cracked, or corroded, which can cause uneven heating or rattling noises during convection baking.

Replacement door latch rod for electric and gas ranges. Installs in the door mechanism to secure the latch assembly. Order a new rod if broken or missing.

Hex flange nut with 10-32 thread secures components in appliances. Replace if stripped, missing, or damaged. Flange provides broader bearing surface.

This backguard kit replaces the upper rear panel and trim on compatible ranges to restore a clean appearance and protect wall and controls from spills and heat. It's a direct-fit exterior repair for damaged, bent, or corroded backguards. What it does:

• Replaces the upper rear backguard panel and trim to restore the range's finished rear appearance
• Protects the control area and wall from splashes, grease, and heat exposure
• Helps stop drafts and gaps behind the range that can collect debris
• Addresses visible damage like dents, rust, or cracked trim

• Disconnect power to the range (unplug or switch off breaker) before starting work.
• Installation may require lifting and aligning the panel; use a second person for safety on larger ranges.
• Use common hand tools; keep fasteners and mounting brackets from the old assembly if reusable.
• Follow the appliance manufacturer's service instructions for model-specific steps and torque values.

This backguard kit replaces the rear trim panel on compatible electric and gas ranges to restore appearance and protect the wall and control area from spills and splatters. Ideal for worn, bent, or damaged rear trim. What it does

• Covers the area behind the cooktop to block grease, steam and food splatter.
• Restores a finished appearance to the back of the range after damage or removal.
• Helps protect controls and wiring routed near the rear from direct splatter.
• Designed to attach to the rear of the range using existing mounting points.

• One backguard kit.

• Installation generally requires lifting or pulling the range forward; use a second person to avoid injury.
• Disconnect power before beginning work.
• Use caution around sharp sheet-metal edges and wear gloves.
• Follow the OEM parts diagram and hardware locations; replace any damaged mounting hardware.

Range burner not heating or temperature won't adjust? This surface element control switch regulates heat output. Moderate DIY repair in 30-45 minutes.

Black mounting screw that secures range body side panels. Replace if stripped, missing, or corroded. 8-18 x 11/16 inch fastener for structural assembly.

Replace your range door gasket when it becomes worn, brittle, or deteriorated to restore proper heat containment and prevent leaks. Confirm fit with your model.

Touch-up paint for appliances to cover scratches, chips, and worn areas on exterior surfaces. Restores appearance of refrigerators, ranges, and more.

A replacement motor latch that secures the motor assembly to the appliance chassis, helping keep the motor stable during operation for smoother performance and reduced vibration. Fits specific Frigidaire/WCI motor assemblies. What it does:

• Secures and positions the motor assembly to prevent excessive movement
• Helps reduce vibration and rattling caused by a loose motor mount
• Restores proper alignment between motor and drive components
• Can eliminate intermittent contact-related noise from a shifting motor

• Disconnect power (unplug or switch off breaker) before starting any repair
• Installation typically requires accessing the motor area—expect to remove panels or the cabinet
• Keep track of mounting hardware; replace any damaged fasteners
• Test operation after reassembly; stop and recheck if noises or vibration persist

Range indicator light lens kit with red and clear lenses. Replace when cracked, discolored, or missing. Fits control panel burner indicators. Verify fit.