Kenmore Refrigerator 795.58823900 (79558823900, 795 58823900) Parts

The Drain Tube Assembly is an OEM part for LG refrigerators. This drain tube assembly is responsible for directing condensation and melt water that accumulates in the refrigerator away to the evaporator pan.

Causes can include cracks developing from limescale or mineral accumulation, flexing fatigue from repeatedly catching drips, or damage from improper cleaning methods.

Symptoms of a bad drain tube assembly include:

• Puddles or leaks developing underneath the refrigerator
• Poor air flow from vents and higher temperatures
• Ice or moisture buildup in refrigerator walls and seals
• Water stains or corrosion appearing inside the unit

This OEM LG part is also compatible with some Kenmore models.

This bracket motor secures and supports the appliance motor assembly, restoring proper alignment and stable operation. Replacing a worn or broken bracket helps reduce noise and prevents motor misalignment that can cause poor performance. What it does:

• Holds the motor assembly in the correct position so the motor runs smoothly and stays aligned.
• Prevents excess vibration and rattling caused by a damaged or cracked bracket.
• Helps stop intermittent motor movement or binding that can affect operation.
• Reduces risk of additional wear to the motor or connected components due to misalignment.

• One bracket motor

• Disconnect power to the appliance before beginning any work.
• Replacement typically requires removing access panels and supporting the motor during removal/installation.
• Inspect surrounding fasteners and mounting surfaces; replace any damaged hardware.

The Ice Door Solenoid Assembly is an OEM replacement part for LG refrigerators. This assembly controls the opening and closing of the ice door, which allows ice to be dispensed from the freezer to the exterior of the appliance. When you request ice, the solenoid activates, opening the ice door and permitting ice to pass through.

Symptoms of a bad Ice Door Solenoid Assembly include:

• Ice door not opening or closing properly
• Failure to dispense ice
• Ice accumulating or jamming at the dispenser

Causes for a malfunctioning Ice Door Solenoid Assembly can include electrical issues such as faulty wiring, wear and tear from frequent use, or mechanical problems affecting the solenoid's ability to move the ice door.

This OEM LG part is also compatible with Sears/Kenmore models.

Note: 90 degree elbow coupler (Fits 1/4" diameter tubing on each end) For 5/16" elbow connector, order part# 4932JA3009B.

The Water Line Union is an OEM part for LG refrigerators. This component connects sections of the water line, ensuring a secure and leak-free passage of water to the refrigerator's icemaker and water dispenser. It is an elbow tube union connector, which connects two tubes at a 90-degree angle.

Causes of a bad water line union can include wear and tear from frequent use, damage from high water pressure, or deterioration due to mineral buildup and age. A compromised union can lead to water leaks and disruption in the water supply.

Symptoms of a bad Water Line Union include:

• Water leaks around the connection points
• Reduced water flow to the icemaker or water dispenser
• Puddles or moisture near the refrigerator
• Unusual noises from the water line

This OEM LG part is also compatible with Sears/Kenmore.

Replace a worn door gasket to restore a tight seal on your refrigerator door. This perimeter seal keeps cold air in and humid air out to stabilize temperatures, reduce frost and condensation, and support efficient, consistent cooling.

• Creates an airtight seal between the door and cabinet
• Helps maintain proper internal temperature and humidity
• Reduces frost, sweating, and energy loss from air leaks
• Common symptoms: torn or hardened gasket, visible gaps, door not sealing, moisture or frost near the door

• Disconnect power before servicing
• Warm the new gasket in hot water or with a hair dryer on low to relax and straighten it
• Remove the old gasket and clean the mounting channel and mating surfaces
• Install starting at the corners and press fully into the channel; verify even contact and proper door closure

This refrigerator door gasket forms an airtight seal between the door and cabinet to keep cold air in and humid air out, helping restore stable temperatures and efficiency when the original seal is worn, torn, or warped.

• Seals the door perimeter to prevent air leaks and temperature swings
• Helps reduce frost and condensation around the door opening
• Can resolve doors not closing fully or popping back open
• Replace if the gasket is cracked, deformed, or won't stay seated

• Disconnect power and clear items from the door before starting
• Warm the new gasket (hot water or low heat) to relax folds and improve fit
• Pull the old gasket from the retaining channel; press the new one in firmly, starting at the corners
• Close the door and check for an even seal all around; allow the gasket to conform over the next 24 hours

Replacement plastic door basket that mounts to the inside refrigerator door to keep bottles, condiments and small items organized and secure. Restores usable door storage and helps prevent items from shifting or falling. What it does

• Holds bottles, jars, condiments and other door-stored items to maximize door storage space.
• Replaces a cracked, broken or missing door bin that no longer secures items.
• Common symptom: items slide, fall out, or the bin is loose or won't stay in place when the door is opened.
• Snaps into the refrigerator door rail to form a stable storage shelf.

• Remove all items from the door before replacing the basket.
• Align the basket with the door rails and press until it snaps into place; reverse to remove.
• Handle with care to avoid cracking the plastic; replace if mounting clips are damaged.

It contains the defrost temperature sensor and the defrost thermal fuse.

A momentary push-button switch that restores reliable button control on the appliance console. Replaces a worn or non-responsive push switch so the control board receives a clear input when the button is pressed. What it does:

• Sends a momentary electrical signal to the control board when pressed
• Replaces broken, stuck, or intermittently working push buttons
• Helps resolve symptoms like no response from the console, intermittent button function, or a physically damaged button
• Functions as the user input for single-press commands

• One momentary push switch

• Disconnect power before servicing to avoid shock or injury
• Access usually requires removing the control panel or console; use appropriate screwdrivers
• Note connector orientation and gently unplug wire harness—do not pull on wires

This replacement fan assembly restores airflow in your appliance's cooling system to help maintain proper temperature and circulation. It's a direct-fit replacement designed to stop airflow-related issues and reduce noise from a failing fan. What it does:

• Circulates air across evaporator/condenser coils to support proper cooling and defrost cycles
• Replaces a worn or failed fan that can cause warm compartments or poor cooling
• Helps eliminate unusual humming, grinding, or rattling caused by a damaged fan blade or motor
• Supports even temperature distribution and can reduce frost buildup when fan operation is restored

• Disconnect power before starting; work on powered appliances can cause shock or injury
• Handle the fan blade carefully to avoid bending blades or damaging the motor
• Secure mounting fasteners to prevent vibration

This fan assembly moves air through the appliance to help maintain proper cooling and airflow. It replaces a worn or noisy fan to restore efficient air circulation and temperature consistency. What it does:

• Circulates air across evaporator or condenser coils to support proper cooling
• Helps reduce temperature fluctuations and frost buildup when functioning correctly
• Stops or slows excessive noise caused by a damaged or unbalanced fan
• Restores airflow when a failed fan motor or blade prevents circulation

• One fan assembly (motor and blade housing)

• Disconnect power before starting any repair to avoid shock or injury
• Handle the fan blades and motor carefully to avoid bending blades or damaging wiring

This lamp cover protects and diffuses the appliance interior light for safer, even illumination. It restores proper light distribution while shielding the bulb from spills, bumps, and debris. What it does:

• Covers and protects the interior lamp assembly to prevent direct contact with the bulb
• Diffuses light for more even illumination inside the compartment
• Helps prevent dirt, moisture, and food particles from reaching the lamp
• Commonly replaced when cracked, discolored, or missing, which can cause glare or uneven lighting

• One lamp cover only

• Disconnect power to the appliance before servicing to avoid shock
• Handle the cover carefully to avoid cracking; use gloves to keep it clean
• Reinstall using the existing clips or screws; ensure correct orientation and secure fit
• If lamp or mounting hardware is damaged, replace those components as well