Lg Washer 40776 Parts

Locking pin for shock absorber.

Fix washer leaks with this hose clamp. Secures hoses to pumps and valves, preventing water leaks and disconnections during wash cycles. Simple repair.

This Leg Adjusting Wrench is a simple tool used to turn and secure appliance leveling legs so washers and dryers sit flat and operate quietly. It makes adjusting legs faster and helps reduce rocking and vibration. What it does:

• Fits over standard appliance leveling legs to raise or lower each corner
• Helps stabilize machines to prevent rocking and uneven operation
• Reduces vibration and noise caused by unlevel appliances
• Useful when installing, moving, or re-leveling washers and dryers

• Turn legs slowly and adjust one corner at a time until the appliance sits level.
• Unplug the appliance (and shut off gas supply for gas dryers) before performing major moves or checks.
• Use caution to avoid pinching fingers when lowering legs; keep hands clear of pinch points.
• Check for damaged feet or mounting hardware and replace as needed.

This clamp secures hoses or wiring to the appliance chassis to prevent movement, chafing, and vibration-related wear. It helps keep connections stable so hoses and wires stay in place during normal use. What it does:

• Holds water, drain or vent hoses in position to reduce strain and prevent rubbing
• Keeps wiring harnesses routed and fastened to avoid chafing or accidental disconnection
• Reduces vibration-related noise caused by loose hoses or wires
• Helps prevent hose kinks and unintended movement that can lead to leaks or intermittent electrical issues

• One clamp

• Disconnect power to the appliance before servicing; shut off water supply if working with water lines
• Remove panels as needed to access the hose or wiring route, then replace the clamp in the same orientation
• Use appropriate pliers or a screwdriver if required; do not overtighten or deform the hose or wiring
• If the original clamp was secured with a fastener, retain and reuse it only if undamaged; replace any stripped or broken hardware

Interior support trim that secures the door assembly and provides a finished surface inside your washer door. Replace when cracked, damaged, or worn.

Cabinet base assembly for washers. Replaces cracked, rusted, or corroded base frames. Installs at bottom of washer cabinet to support unit weight.

Drum bearing bushing for washers. Installs between drum and bearing assembly. Replace if cracked, worn, or missing to restore proper drum support.

Secures internal washer components and maintains proper alignment. Replace when brackets are worn, broken, or causing rattling. Confirm fit with your model number.

Replace your washer's hose connector if cracked, broken, or leaking. This mechanical fitting secures water hoses to your washing machine inlet or drain system.

Leveling leg assembly for washers and laundry centers. Installs at the base to support and level the unit. Replace if cracked, broken, or missing.

This replacement refrigerator door handle restores a secure grip and normal door operation after a cracked, broken, or loose handle. Designed to match the original fit and finish for a clean, factory look. What it does

• Provides a functional grip so doors open and close reliably
• Replaces cracked, bent, or detached handles that prevent safe operation
• Restores proper alignment and reduces door movement or wobble
• Helps maintain an airtight seal by allowing the door to fully close

• Use basic hand tools; avoid power tools that can strip fasteners
• Keep door supported while removing/installing the handle to prevent damage
• Do not overtighten screws—secure snugly to avoid cracking the handle

Replacement handle for laundry center doors. Installs on front panel for opening and closing access. Needed when original is cracked, broken, or missing.

This drain hose cap seals the end of a dishwasher or washer drain hose to prevent leaks and help keep odors and debris from entering the drain line. It restores a snug, secure hose termination for reliable draining. What it does

• Seals the open end of a drain hose to reduce water leaks at the hose termination.
• Helps prevent sewer odors or debris from traveling back through the hose.
• Keeps hose connection clean and reduces risk of clogging at the open end.
• Useful when replacing a damaged or missing hose end cap to maintain proper drainage.

• Disconnect power and turn off water supply before servicing the appliance.
• Remove the old cap and inspect the hose end for damage or buildup; clean as needed.
• Push the cap onto the hose end until fully seated; verify a snug fit and no visible gaps.
• Test by running a short drain cycle and checking for leaks; replace if cap doesn't seal.

Replacement hose connector for washer installation and stacking kits. Connects water supply lines during setup. Replace if cracked, leaking, or missing.

Washer manual holder that secures care guide documentation to your appliance. Replace if cracked, broken, or missing to keep owner's manual accessible.