Lg Washer 40776 Parts

Joins two internal water lines in your washer. Replace this coupler if cracked, worn, or leaking to restore a secure connection during fill and wash cycles.

This washer tub assembly is the stationary outer drum that contains wash water and supports the spin basket and drive components. Replace a cracked or worn tub to stop leaks and restore smooth, quieter spin performance.

• Forms the sealed outer container for wash water and houses the spin basket
• Provides mounting points for suspension, motor, and hoses (varies by model)
• Keeps the basket aligned for balanced, quiet operation
• Typical symptoms of failure: water leaks, roaring/grinding during spin, excessive vibration, or visible cracks

• Unplug the washer and shut off water; the tub is bulky—use two people and wear gloves
• Remove panels as needed for access, then disconnect hoses, wiring, suspension, and drive components to free the tub
• Transfer all reusable parts from the original tub to the new tub in the same orientation
• After reassembly, check for leaks and run a test cycle/spin to verify operation

This is the internal fill hose that connects the water inlet valve to the wash tub inside the washing machine, delivering cold water during the fill cycle. It is a rubber or reinforced hose with fittings on each end. Replace this hose if you notice leaking underneath or behind the washer, or if the machine is not filling properly with water.

Seals the gap between washer tub and door opening to prevent leaks. Replace if torn, cracked, or deformed to restore watertight seal. Verify fit.

Secures rubber hoses to fittings with constant spring tension to prevent leaks. Replace when rusted or weakened to maintain a tight seal. Confirm fit.

Fix washer leaks with this hose clamp. Secures hoses to pumps and valves, preventing water leaks and disconnections during wash cycles. Simple repair.

This Leg Adjusting Wrench is a simple tool used to turn and secure appliance leveling legs so washers and dryers sit flat and operate quietly. It makes adjusting legs faster and helps reduce rocking and vibration. What it does:

• Fits over standard appliance leveling legs to raise or lower each corner
• Helps stabilize machines to prevent rocking and uneven operation
• Reduces vibration and noise caused by unlevel appliances
• Useful when installing, moving, or re-leveling washers and dryers

• Turn legs slowly and adjust one corner at a time until the appliance sits level.
• Unplug the appliance (and shut off gas supply for gas dryers) before performing major moves or checks.
• Use caution to avoid pinching fingers when lowering legs; keep hands clear of pinch points.
• Check for damaged feet or mounting hardware and replace as needed.

Does not come with a hose or filter. These have to be purchased separately

Pivot hanger assembly that supports and stabilizes washer components. Replace if worn, damaged, or causing misalignment to restore smooth movement.

This replacement knob assembly restores tactile control for a range or cooktop control. It provides a secure grip and clear detent positions so you can set burner or surface settings reliably. What it does:

• Replaces a worn, cracked, or missing control knob to regain safe, predictable control
• Engages the shaft and detents so settings stay put during use
• Helps eliminate slipping or difficulty turning the control
• Matches original fit and function for direct replacement

• One knob assembly as shown

• Turn power/gas to the appliance off before servicing; follow appliance manufacturer safety instructions
• Remove the old knob by pulling straight off the control shaft; press the new knob onto the shaft until it seats
• Wear work gloves to protect hands from sharp edges during access

Fix water leaking from your washer dispenser or misdirected flow with this dispenser water guide channel. Routes water properly to prevent splashing.

This metal hook mechanism secures the washing machine door in the closed position during wash cycles for safe operation. It engages with the door strike to create a tight seal and prevent the door from opening while water is present. Replace if the door won't latch securely, pops open during cycles, or won't unlock after washing.

Drum bearing bushing for washers. Installs between drum and bearing assembly. Replace if cracked, worn, or missing to restore proper drum support.

Outer door frame for front-load washers. Plastic housing that surrounds the door glass. Replace if cracked, broken, or damaged from impact.