Lg Range LSSG301 Parts

Uneven flame or poor heating? This gas range burner cap directs flames evenly across cookware and contains sparks. Simple snap-on installation.

Secures the control panel to your range cabinet. Replace if the bracket is cracked, bent, stripped, or hardware no longer holds the console firmly in place.

Replace worn range drawer sliders to restore smooth, quiet operation and proper alignment. Prevents damage to surrounding trim. Confirm fit with your model.

Control knob assembly for gas ranges and cooktops. Installs on the control panel to operate burners and oven settings. Replace cracked, loose, or missing knobs.

Fixes uneven flames and improves heat distribution. This burner cap covers the burner head to direct flame properly and protect against debris buildup.

If your gas range has uneven flames, yellow or orange flames, or won't light properly, a damaged burner cap is often the cause. This part restores safe, even heat distribution.

This is a metal cover that shields the convection fan and heating element inside the rear wall of the oven cavity. It protects the fan assembly from grease and food debris while allowing heated air to circulate evenly throughout the oven. Replace this cover if it is warped, corroded, or damaged, which can lead to uneven cooking or unusual noises during convection baking.

Replace your range's outer door frame to restore door structure, improve seal integrity, and fix cracked or bent trim. Confirm fit with your model number.

Replacement screw for electric and gas ranges. Secures panels, brackets, and internal assemblies. Restores tight fit when original is missing or stripped.

Bracket that anchors the handle to your range oven door. Replace if cracked, stripped, or broken to restore secure handle attachment and alignment.

This bracket secures the turntable motor to the microwave oven cavity base, keeping the motor properly aligned so the glass tray can rotate smoothly for even heating.

• Supports and positions the turntable motor beneath the oven floor
• Helps resolve issues like a non-turning glass tray or jerky rotation
• May correct intermittent grinding or scraping noises from the tray area

• Unplug microwave before servicing; high-voltage components can retain a charge
• Remove the unit from its install location if required for bottom access
• Access turntable motor from the underside; support the cavity to prevent damage
• Reuse existing screws and motor unless otherwise specified

Fix control issues or power failures with this gas range cable assembly. Restores reliable operation when wiring is damaged, burned, or has loose connections.

This power control board assembly replaces the appliance's sub power board to restore electronic control of cycles and power distribution. It fits into the control module area and provides the relay and circuit functions the machine uses to run. What it does:

• Controls power routing to motors, heaters and other major components through relays and circuitry
• Interfaces with the main control to execute cycle commands and timing functions
• Can resolve intermittent power loss, unresponsive controls, or failure to start when caused by a faulty sub board
• Helps stop erratic operation caused by burned traces, failed relays, or damaged components on the sub PCB

• Install only with the appliance unplugged and power disconnected to avoid shock or damage
• Handle the PCB by the edges and avoid touching components to prevent ESD damage
• Confirm connectors are fully seated and screws are tightened to factory torque; double-check wiring matches the removed board

Surface burner grate for gas ranges and cooktops. Sits atop burner to support cookware during cooking. Replace if warped, cracked, broken, or chipped.

This is a replacement screw used to secure appliance components and panels. It restores proper fastening where a stripped, missing, or damaged screw causes loose parts or rattling. What it does:

• Fastens panels, trim, or internal components to maintain structural fit
• Helps stop vibration-related noise from loose assemblies
• Replaces missing or corroded screws that prevent proper closures
• Restores secure mounting after repairs or disassembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not over-torque to prevent thread damage
• Keep small parts away from children and pets
• Disconnect power or water before accessing internal parts

Fix range display not working, oven not heating, or control panel errors with this power control board assembly. Moderate DIY repair for ranges.