We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
This Screw (drawing) is a factory fastener used to secure appliance panels and components. Replacing a stripped, corroded, or missing screw restores a tight fit, reduces vibration, and helps keep assemblies correctly aligned.
The upper counter-balance weight mount design is a poor design to begin with. It started to rattle loose approximately 5yrs into the 8yrs that we've owned it. As it would start to loosen up (as evidenced by the loud banging noise exhibited during operation); I'd shut it down, pull the top off, remove the weight (it was almost always half rattled off at this point), wrap the mount lugs with friction tape (the plastic lugs were being worn down/chaffed by the balance weight), put the weight back... Read more
Most orders arrive by Wednesday, November 25
Channels household water to your washer's fill system. Replace if cracked, leaking, or worn to restore proper flow and prevent water damage to floors.
Replaced Read more
Secures hose connections to prevent leaks in your washer. Replace if corroded, rusted, or leaking around hose fittings. Confirm fit by model number.
Replacement Read more
This rubber fill hose connects the household hot water supply valve to the washing machine's water inlet valve. It delivers hot water into the wash tub during the fill cycle. Replace this hose if it is cracked, leaking, bulging, or showing signs of deterioration to prevent water damage.
Joins two internal water lines in your washer. Replace this coupler if cracked, worn, or leaking to restore a secure connection during fill and wash cycles.
Following what I've seen or watched from you tube video clinic "how to replace drain pump for LG Washer, model wm2277hw and the help that I received from representative/ customer service of appliacepartspros, I fixed our LG Washer no problem. I am very much thankful to the representative of AppliacePartsPros who help me analyzed the problem and recommended the right parts that I needed and most importantly arrived 2 days as ordered. I would recommend AppliacePartsPros for ordering your parts. Read more
This is the internal fill hose that connects the water inlet valve to the wash tub inside the washing machine, delivering cold water during the fill cycle. It is a rubber or reinforced hose with fittings on each end. Replace this hose if you notice leaking underneath or behind the washer, or if the machine is not filling properly with water.
Mounts to the washer's lower frame to secure components and maintain alignment. Replace if bracket is cracked, broken, rusted, or missing hardware.
Replaced leg mount and leg. Read more
Secures rubber hoses to fittings with constant spring tension to prevent leaks. Replace when rusted or weakened to maintain a tight seal. Confirm fit.
Fix washer leaks with this hose clamp. Secures hoses to pumps and valves, preventing water leaks and disconnections during wash cycles. Simple repair.
This Leg Adjusting Wrench is a simple tool used to turn and secure appliance leveling legs so washers and dryers sit flat and operate quietly. It makes adjusting legs faster and helps reduce rocking and vibration. What it does:
AppliancePartsPros had the needed items in stock, and I had them within 48 hours of the parts being shipped. Read more
Pivot hanger assembly that supports and stabilizes washer components. Replace if worn, damaged, or causing misalignment to restore smooth movement.
I ordered both the hot and cold water inlet valves because I wasn't sure which one may have been faulty. I installed them exactly the way the on line video showed, tested them and reinstalled the top of the washer. Checked several days and have found no sign of water. This was such an easy fix! Read more
Replaces the outer tub cover panel on front-load washers. Protects internal components and maintains drum alignment. Order when cracked or damaged.
Inlet hose connects your washer to the water supply. Replace if cracked, leaking, worn, or damaged to restore proper water flow to your machine.
Supports smooth drum rotation in your washer. Replace if you hear loud roaring or grinding noises during spin cycles. Confirm fit with your model number.
Replaced the failing bearings and seal to eliminate loud noise during spin cycle. First the positive feedback regarding the video provided saved time and efforts and was VERY helpful. I called customer services to review the parts I was ordering. I was provided the wrong information and back bearing for the drum. Reordered the correct one which came quickly and was supplied RMA for refund with correct bearing. It took several weeks to issue a notice of refund and will take longer to be posted... Read more
Usually ships within 4 - 14 days
Pressure sensor air chamber for washers. Connects the tub to the water level switch. Replace if cracked, clogged with detergent residue, or leaking air.