Lg Washer WM2377CS Parts

This is the internal fill hose that connects the water inlet valve to the wash tub inside the washing machine, delivering cold water during the fill cycle. It is a rubber or reinforced hose with fittings on each end. Replace this hose if you notice leaking underneath or behind the washer, or if the machine is not filling properly with water.

Seals the gap between washer tub and door opening to prevent leaks. Replace if torn, cracked, or deformed to restore watertight seal. Verify fit.

Secures rubber hoses to fittings with constant spring tension to prevent leaks. Replace when rusted or weakened to maintain a tight seal. Confirm fit.

Fix washer leaks with this hose clamp. Secures hoses to pumps and valves, preventing water leaks and disconnections during wash cycles. Simple repair.

This replacement knob assembly restores tactile control for a range or cooktop control. It provides a secure grip and clear detent positions so you can set burner or surface settings reliably. What it does:

• Replaces a worn, cracked, or missing control knob to regain safe, predictable control
• Engages the shaft and detents so settings stay put during use
• Helps eliminate slipping or difficulty turning the control
• Matches original fit and function for direct replacement

• One knob assembly as shown

• Turn power/gas to the appliance off before servicing; follow appliance manufacturer safety instructions
• Remove the old knob by pulling straight off the control shaft; press the new knob onto the shaft until it seats
• Wear work gloves to protect hands from sharp edges during access

This metal hook mechanism secures the washing machine door in the closed position during wash cycles for safe operation. It engages with the door strike to create a tight seal and prevent the door from opening while water is present. Replace if the door won't latch securely, pops open during cycles, or won't unlock after washing.

Protective access cover shields internal washer components from dirt and moisture. Replace if cracked, broken, or missing to restore factory protection.

Washer won't spin or agitate? A faulty stator assembly disrupts the magnetic field needed to drive the motor. Restores normal drum rotation.

Outer door frame for front-load washers. Plastic housing that surrounds the door glass. Replace if cracked, broken, or damaged from impact.

Replaces the outer tub cover panel on front-load washers. Protects internal components and maintains drum alignment. Order when cracked or damaged.

Replaces worn or torn door boot gasket that seals your washer drum. Replace if you notice water leaks, mold buildup, or visible cracks. Confirm fit.

A replacement holder assembly that secures and supports internal components for proper alignment and operation. Restores stable mounting where the original bracket is cracked, bent, or broken so the appliance runs quietly and reliably. What it does

• Provides a secure mounting point for internal parts that rely on a fixed support
• Prevents rubbing, misalignment, and excess vibration caused by a damaged holder
• Helps restore correct component positioning to improve part interaction and operation
• Commonly used when the original bracket is cracked, worn, or no longer holds parts firmly

• One holder assembly

• Disconnect power before starting any repair; shut off water supply if the repair requires opening plumbing
• Basic hand tools typically required; handle clips and tabs gently to avoid damage
• Inspect adjacent components for wear and replace if needed for a long-lasting repair

The washer Hose Retainer Holder Clip is an OEM part that mounts behind the control panel on LG front-loading washers. It positions water supply hoses to prevent kinks or stress that leads to leaks over time. 

Causes of a failed clip include fatigue from years of front-load vibration and damage from any installation or repair work behind the control panel.

Symptoms of an insufficient hose retainer clip include:

• Loose, misrouted, or flopping hoses behind the control panel
• Bulging or kinked hoses that restrict water flow
• Water leaks at hose connections

This OEM replacement clip is compatible with select Kenmore front-loaders.

Supports smooth drum rotation in your washer. Replace if you hear loud roaring or grinding noises during spin cycles. Confirm fit with your model number.

Pressure sensor air chamber for washers. Connects the tub to the water level switch. Replace if cracked, clogged with detergent residue, or leaking air.