Parts for Maytag MVWB835DC0: 05 - Pump Parts

This washer drain pump moves water out of the washer during drain and spin. Replacing a worn or failed pump restores proper draining so cycles finish on time and the basket can reach full spin speed.

What it does

• Pumps water from the tub to the household drain during the drain cycle
• Helps resolve standing water, slow draining, or humming from a seized pump
• Reduces long/aborted cycles caused by incomplete draining
• Can stop leaks at the pump body when the housing is cracked

What’s included
One drain pump assembly.

Install notes

• Unplug power and turn off water; bail out remaining water before service
• Clamp/remove hoses and keep towels handy; transfer any mounting bracket as needed
• Inspect and clear the drain hose and tub-to-pump hose before reassembly
• Run a drain/spin test to verify proper flow and check for leaks

This OEM drain pump is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

This factory fastener secures appliance panels and components for a tight, rattle-free fit. Replace a missing, stripped, or corroded screw to keep assemblies aligned and performing as intended.

• Fastens panels, brackets, or assemblies in place
• Helps reduce vibration and rattling caused by loose hardware
• Maintains proper alignment of parts to prevent premature wear
• Common signs you need it: missing screw, loose panel, vibration/buzzing noises, or hardware that won't tighten

• Disconnect power; for gas or water-connected appliances, shut off supply lines before service
• Match the screw to the original; verify size, length, and thread before installation
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Snug only—do not overtighten, especially into plastic or thin sheet metal

The Tub to Pump Hose is an OEM replacement part for Whirlpool washing machines. It serves as the connecting pipe linking the washing machine tub to the pump.

Common causes of hose damage relate to extended use, exposure to harsh chemicals within machine drain water, and physical stress from years of frequent bending during operation.

Symptoms of a failed tub-to-pump hose include:

• Water leaks developing beneath or behind the machine
• Straining noises and reduced water pressure during cycles
• Deterioration of hose material exposing cracks or leaks

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

This factory screw fastens appliance components securely. Replacing a missing, stripped, or rusty screw helps stop rattles, keep panels and brackets aligned, and restore a solid, as-designed fit.

• Secures panels, brackets, and trim to the appliance cabinet or frame
• Helps maintain alignment and reduce vibration or rattling noises
• Replaces damaged, corroded, or missing hardware
• Can resolve loose or shifting components

• Disconnect power and shut off gas/water to the appliance before service.
• Use the correct driver; start threads by hand to avoid cross-threading and do not overtighten.
• Install in the original location and match the OEM fastener type specified in your model's parts diagram.