Parts for Kitchenaid KDTM404KPS0: Pump, Washarm And Motor Parts

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Dishwasher not cleaning dishes or cycle won't complete? The circulation pump distributes water during wash and rinse cycles. Moderate DIY repair.

Quantity of ONE. Size: 8-18 x 5/8 inch. (#8 screw, 18 threads per inch, 5/8 inch long)

Fixes dirty water or food specks remaining after wash cycles. This check valve prevents backflow into the dishwasher sump. Moderately easy repair.

Replacement spray arm for your dishwasher. This rotating component distributes water throughout the wash cycle. Replace if cracked, broken, melted, or missing pieces.

Screens debris from entering the pump and wash arms. Replace if damaged, shredded, or causing poor drainage. Verify fit with your model number.

Precision ring that positions and secures internal dishwasher components. Replace when worn, cracked, or missing to restore proper fit and alignment.

Fixes dishwasher not spraying water or poor circulation. This pump and motor assembly circulates water through spray arms. Moderate DIY repair.

Mounting bracket that secures and stabilizes internal dishwasher components. Replace when original support is cracked, bent, or missing to restore alignment.

The Hose is an OEM part for Whirlpool dishwashers. It connects the dishwasher pump and sump, functioning to drain and recirculate water throughout cycles.

Causes of failure can include mineral buildup inside the hose, splitting, and cracking of the lining from continuous heat and pressure usage over time.

Symptoms of a bad pump to sump hose include:

• Inadequate drainage and water removal from cycles
• Standing water left in the bottom of the dishwasher tub
• Leaks developing from hose connections at the pump or sump area

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Flexible drain hose that routes wastewater from your dishwasher to the household drain. Replace if cracked, kinked, leaking, or showing wear and tear.

Fix a dishwasher that won't drain or shows F9E1 error code. This drain pump removes water during the drain cycle. Moderate DIY repair for most models.

Drain hose connects your dishwasher drain pump to household plumbing. Replace if cracked, kinked, clogged with grease, or leaking during drain cycles.

Fix uneven drying or excess noise caused by poor air circulation. This dishwasher airflow diffuser restores proper air distribution for consistent performance.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

The Sensor is an OEM replacement part for Whirlpool dishwashers. It detects the level of dirt and food particles in the wash water to help the dishwasher adjust the wash cycle accordingly, providing efficient and thorough cleaning results. It monitors the clarity of the water and determines when additional rinsing or detergent is needed.

Symptoms of a faulty sensor include:

• Inadequate cleaning performance
• Dishes remaining dirty or stained after a wash cycle
• Extended cycle times or the dishwasher not completing the cycle

A bad sensor can occur due to regular usage, buildup of residue or debris, or electronic malfunctions. If you notice issues such as poor cleaning results, dishes not being thoroughly washed, or the dishwasher not completing the cycle, it may be time to replace the sensor with this genuine OEM part.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

Dishwasher overheating or shutting off mid-cycle? This high limit thermostat monitors temperature to prevent damage. Fixes common heating issues.

If your dishwasher won't fill with water or shows an H20 error, the inlet valve likely needs replacement. Basic tools required, 30-minute repair.

Secures hose connections to circulation motor and sump in your dishwasher. Replace if loose or worn to prevent leaks. Confirm fit with your model number.

The Drain Hose is an OEM part for Whirlpool dishwashers. It channels water out of the dishwasher tub and into the garbage disposal or drain after each cycle. This drain hose is specifically designed to withstand frequent temperature fluctuations and mineral deposits without compromising its integrity over time.

Causes of a bad Drain Hose can include mineral buildup inside the hose restricting flow, cracks developing from repeated flexing during drain cycles, or cuts or abrasions from rough handling or sharp surfaces.

Symptoms of a bad Drain Hose include:

• Water not draining properly or draining slowly after cycles
• Puddles or leaks found near or under the dishwasher
• Musty smells from standing water inside or around the unit
• Possible flooded floors near the dishwasher area

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Clip is an OEM part for Whirlpool dishwashers. It securely attaches the drain hose in place, directing wastewater out of the dishwasher during drain cycles.

Causes of a bad clip can be cracks, breaks, or deformations causing weakened grip. Normal wear and repeated drain cycles can also damage the clip over time.

Symptoms of a bad drain hose clip include:

• Water or leaks around the base of the dishwasher
• Puddles forming due to the hose slipping out of place
• Improper drainage if the hose is not positioned correctly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Secures hose connections to circulation motor and sump in your dishwasher. Replace if loose or worn to prevent leaks. Confirm fit with your model number.

The Inlet Hose is an OEM part for Whirlpool built-in dishwasher models. This hose delivers fresh water from the household supply to the appliance spray arms and pumps. 

Symptoms of a faulty inlet hose include:

• Leaks or drips around hose connections  
• Kinks or cracks in the supply line tubing
• Restricted or no water flow to critical systems
• Improper water levels causing wash performance issues

Causes can be deformation from tight bends over time. Mineral buildup inside the hose is also common with extended use. Accidental damage during plumbing work presents another potential cause.

This authentic Whirlpool replacement is compatible with some Maytag, Jenn-Air and Amana dishwasher brands as well.

Secures hoses to fittings and prevents leaks in your dishwasher. Replace when connections loosen or water escapes. Confirm fit with your model number.

Traps food particles and debris to prevent drain clogs and maintain optimal water circulation. Replace when cleaning no longer restores performance. Confirm fit with your model number.

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Leaking under your dishwasher or water pooling after cycles? The sump assembly houses the motor and pump. Requires disassembly; check hoses first.

Dishwasher motor hums but won't start? This capacitor provides the phase shift needed for your circulation motor to run. Easy 15-minute repair.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.