Willy December 29, 2011 for Model Number SHE45M05UC The dishwasher doesn't fill up with water. I checked the water line and it looked okay.
1 Answer Hello Willy. Check and make sure the float is not stuck in the unit. If not, and there is power to the water valve, you will need to replace the water valve in the unit. Hope this helps. Read More...
Don R. December 21, 2011 for Model Number Bosh shu43co5uc/17 The unit starts normally drains tub - fills tub - starts to wash runs 3 to 5 seconds and stops 10 seconds goes by and runs 3 to 5 seconds again this continues until on off button is pushed.
1 Answer Hi Don. This is a control board issue.Control Module - Made by Bosch. Common program control module for Bosch dishwashers SHU53/68. NOTE The manufacturer has redesigned the cover and indicator lights. Lights may be covered by the plastic case. You may have to remove the square covers over the indicator lights if needed. The same case is used for 6 and 8 indicator light models. They also no longer use the red bulb indicator lights, small surface mounted lights are used instead. Part Number: 00266746. Remember to use dishwasher magic monthly part # TJ104 or Glisten part # W10549845, to keep the unit jets , filters and the sump pump clean. This will sustain proper performance and keep the optical water sensor clean for sensing the cleanliness of the water. Thank You. Read More...
Izzy November 01, 2011 for Model Number SHU6800 Thank you for the answer. I checked the water and it actually is coming in to the washer at over 120, I ran it again and half way thru the cycle I opened it to check the actual water temp in the washer and it was luke warm at best, and of cousre took over 2 hours to complete the quick was cycle. Not sure what to do at this point.
1 Answer Hello Izzy. Based on the information you provided, it sounds like the heater assembly 00263869 is bad and will need to be replaced. Hope this helps. Read More...
Chris W. October 22, 2011 for Model Number SHU5315UC/12 Fills with waters, doesn't start washing? I just replaced the module.
1 Answer Hi Chris. Is it giving any flashing codes? Is the motor humming like the impeller is Bad? See your e-mail instructions to aid you. Thank You. Read More...
Andrew October 21, 2011 My son has a bosch clasixx dishwaser and it has stopped heating up the water, it still finishes the cycle but soap dispenser remains closed and full of congealed soap. Help me dad!!!
1 Answer Hello Andrew. Test and see if there is power going to the heater assembly during the drying process. If so, and the heater does not come on, you will need to replace the heater assembly. Hope this helps. Read More...
Bayoubrewer October 07, 2011 for Model Number SHU5306UC/U11 Unit starts showing 2H, on delicate/economy cycle. Stays there for at least a half hour then moves to 93 then it takes forever to wash. Then 11 comes up and it takes another long time to finally reach 1 then it continues to run until it decides to shut down, the dishes do come out clean and very hot. It show's 2h no matter what you want to start it on HELP !!!
1 Answer Hello Bayoubrewer. Based on the information you provided, it sounds like the control module 00266746 is bad and will need to be replaced. Hope this helps. Read More...
Mtc83 October 07, 2011 I have a Bosch dishwasher which is not emptying water in the bottom of the dishwasher upon completion of the cycle. We have checked the drainage hose to make sure it was free of clogs, replaced the pump, and made sure that the filter is free of clogs. Could it possibly be the modulator? For whatever reason it seems that the pump is not being switched on. The water level fills up to the point where the sensor tells the dishwasher to interrupt the cylcle and drain but it never drains fully. Thanks!
1 Answer Hello MTC83. If there is no power coming to the drain motor, and the unit is in the drain cycle, you will need to replace the control module. Make sure there is no broken wires on the unit, and that the float is not stuck and making the unit think that it is empty. Hope this helps. Read More...
George September 30, 2011 for Model Number SHU6805 Hey guys, Replaced a control module 266746 4 yrs ago due to electronic issues. Now, 2 buttons marked "Quick Wash" and "Rinse and Hold" will not actuate (buttons won't push in). Does the control module need to be replaced again or is the problem something else? Thanks for your help.
1 Answer Hello George. Remove the buttons and make sure they are not stuck. If not, you will need to replace the control module 00266746. Hope this helps. Read More...
Workhorse247 September 18, 2011 My 500 series dishwasher will not empty water out after washing. What are my options? Thanks
1 Answer Hi Workhorse247. You can unhook the drain hose in a bucket from under the sink. Press drain/cancel ans see if it will empty. Check the end of the drain hose and the sink hook - up to see if either are clogged. Is the pump getting 120vac and has the pump impeller clogged or come loose on the motor shaftAP5176436? Please send us the exact model # so we can provide pump part # . You can also use the dishwasher clean/magic or glisten part # W10549845. Thank you. Read More...
Keith September 05, 2011 for Model Number SHU5306UC/U12 Great website. Dishwasher starts with either 2H or 74 in the display. Everything sounds and seems normal. The display eventually reaches "1" where it continues to rinse (forever?). It never goes into a drying cycle. Dishes are clean and hot, evaporation dries dishes and insides of dishwasher quickly if left open. I thought it might be control module but read one of your posts about a heating or heating sensor problem. What's my next move? Thank you. BTW: When this problem started I opened the door panel to see if everything was still connected and didn't find anything wrong but it worked fine for two or three uses afterward.
1 Answer Hello Keith. It sounds like the heater 00480317 is bad. You will need to test for 120 volts going to the heater in the dry mode. If voltage is not there, you will need to replace the control board 00266746. If there is voltage there, you will replace the heater assembly. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...