Dee November 29, 2021 for Model Number SHE4AM15UC/01 Hello, my Bosch dishwasher is about ten years old. The waster starts and runs for about two minutes and then it stops and the clean light notification comes on. If I open and close the door while it is in this two minute cycle, it will start to operate sometimes. Would could cause this problem. I appreciate your response.
1 Answer Dee, For this issue, the most likely cause of the unit not starting will be a faulty control module. Read More...
Earl March 12, 2021 for Model Number Bosch SHE 44co5uc revolution 500 series Dishwasher does not heat water but goes through full wash cycle. When I add one gallon of water to the unit , the dishwasher works ? Does this mean the fill valve needs cleaning or replacement ? If this is the problem which is the correct model # of fill valve I might need? Thank you
1 Answer Earl, If the dishwasher is filling with water and going through the complete cycle but does not heat then it would not be a valve issue. If there is cold water running into the dishwasher then it would be an issue that the water supply is not hooked up to the hot water supply and would need to be switched. If the water is not getting hot enough the dishes will not clean properly. If the water is hooked up properly then it sounds likely that the heater is going to be the issue with the unit. Read More...
Brian January 26, 2021 for Model Number SHE4AM15UC/01 Hello, I have a 12 year old Bosch dishwasher model # SHE4AM15UC/01. It has stopped getting hot during the drying cycle and the "Sanitized" light no longer comes on. The repairman from Bosch told me I needed a new heat pump, which I ordered ($200) and installed, but that didn't fix the issue. I'm not sure what to try next. Also, is there a way to determine if the original heat pump really is defective by measuring continuity across the spade connectors? Thank you.
1 Answer Brian, the heat pump element can be tested for resistance at the 7 wire connector and it should measure 8.9O from pin 2 to pin 3. The NTC resistance should be 10KO from pin 4 to 5, and from pin 5 to 6. There should be a resistance of 20KO from pin 4 to 6. If there is not a loose connection or a damaged wire, the failure would likely be in the user interface control 00668460 if the other selection buttons properly operate. Read More...
Jim October 19, 2020 for Model Number SHE4AP05UC/03 Recently, my Bosch dishwasher (regardless of mode) will not actually clean the dishes. I can start it the Active light comes on and then after ~60 seconds it goes to "Clean". No soap has been dispensed and the dishes are still dirty. I was thinking the Control Unit would need to be replaced, but would like to see if it might be something else. Thanks in advance.
1 Answer Jim, as the dishwasher is short cycling, the failure would be in the control 00701523 based on the information provided. Usually, the failure in another part would cause an excessively long run time rather than a short cycle. Read More...
R Mcduffee December 27, 2019 for Model Number Bosch AHE4AM12UC/02 On your site is posted the following: "My dishwasher will not start when start button pushed. It seems to go into the auto shutdown mode and in about a minute the clean light comes on. The soap dispenser is still closed and no water has run. Initially, it was only in some modes and never occurred with delayed start; however, now it occurs with almost all attempts in any setting, even delay mode. It acts the same as when I push and hold the start button for 30 seconds to shut down. I was thinking of replacing the control unit. Amy for Model Number SHE4APO6UC/06 Answer Hello Amy, The power module 00701523 will need to be replaced to correct this error on model SHE4AP06UC/06. " I have exactly the same problem (different model). In light of the intermittency of the problem, is it really the power module, rather than the control board? Thank you.
1 Answer R McDuffee, the symptoms described indicate that the unit is intermittently not sensing that the door is closed. This can be tested during failure by testing at the door latch hall sensor for a voltage reading. If there is less than 10V, then the issue is in the power module control 00701523. If there is more than 10V, then the issue is in the latch hall sensor 00611312. Read More...
Amy September 25, 2016 for Model Number SHE4APO6UC/06 My dishwasher will not start when start button pushed. It seems to go into the auto shutdown mode and in about a minute the clean light comes on. The soap dispenser is still closed and no water has run. Initially, it was only in some modes and never occurred with delayed start; however, now it occurs with almost all attempts in any setting, even delay mode. It acts the same as when I push and hold the start button for 30 seconds to shut down. I was thinking of replacing the control unit.
1 Answer Hello Amy, The power module 00701523 will need to be replaced to correct this error on model SHE4AP06UC/06. Read More...
Perry P. March 07, 2014 for Model Number Bosch Dishwasher Model SHE4AP06UC/06 I have been having some problems with my Bosch dishwasher. At first it would run some of the cycles short then come back too soon with 'CLEAN, light on. For the Power Scrub it would come back in a few minutes versus 2 hours or so when working. In the auto wash mode it would work most of the time and get things clean. But still some time the clean light would not go off when the door was opened - it seemed to me that was due to some problem in that cycle. I decided to replaced the Control Timer board and that seem to have fixed it about 75% percent. The power scrub run longer, but last time the soap dispenser did not open. I think the Auto wash may have skipped a bit this time as well. Do you think I have a bad Timer Controller again or could the control board behind the panel buttons be bad as well? Thanks
1 Answer Hello Perry, This sounds like an issue with the main control 00701523 on this unit. Read More...
Annmendz October 08, 2013 for Model Number SHE4AP06UC/06 I need to find the control board for the Model number I listed. Bosch SHE4AP06UC/06
Kristi G August 06, 2013 for Model Number she4ap06uc/05 I called the Bosch part number and they gave me this part number 00668460, but when I cross matched my model numer with this part number it says it is not compatible. Please help!!
1 Answer Kristi, The Control unit part number 00668460 is the correct part number for your unit. Read More...
Khanh H June 18, 2013 for Model Number bosch she44m15uc/03 Hi! I think my control board is bad. Can I use this control board ( 668460 ) for my dishwasher? Please help. Thanks.
1 Answer Hello khanh h. The model number you provided is not working. We will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...