Kathleen October 16, 2021 for Model Number NGM8054UC/03 Center burner intermittently clicks, sometimes it is a few clicks and sometimes it is prolonged ( continuous for a few minutes ). This happens while burner is off or on. I have unplugged the power supply to avoid further damage. Trouble shot per manual, issue continues. What part or parts should I order to correct the problem ?
1 Answer Kathleen, You will need to check with a multimeter the wiring to the ignitors and the ignitor switches for breaks and shortages. Read More...
Jim May 25, 2020 for Model Number NGN 8654 UC /3 I'm have an igniter problem and need to remove the jets to get inside the cook top but they are stuck. I'm worried that I will brake something inside if I put too much torque on it. Any tips?
1 Answer Jim, the jets can be heated up by placing the caps on, igniting the burner with a match, and letting it heat for a couple of minutes. From there, with the flame off, the cap would need to be removed using tongs and placed on a grate. A cold, damp washcloth can be used on the venturi to cause the venturi to retract while the holder remains warm, this will allow the venturi to be removed. If the venturi will not come out using this procedure, the venturi and jet holder may need to be replaced as the venturi may need to be cut out. Read More...
Roy April 21, 2020 for Model Number Bosch cook top, model NGM All five burners have started to burn an orange flame.
1 Answer Roy, If the unit is on LP gas then check to make sure that the gas tank is not running low on fuel. For either Lp or Natural gas make sure that the burners are clean, make sure that the orifices are clean. Other than an unclean burn this would be the most likely causes for orange flames. Read More...
Lori October 25, 2019 for Model Number NGM5664UC/03 This is a follow up with more information that wasn't included in my original question. The burner I'm having an issue with is the front left burner, It will light when I use a lighter. The burner does spark and click and gas is flowing. All other burners work just fine and ignite right away. The front left burner gets used 99% of the time and is used several times a day. Thanks
1 Answer Hello Lori, You should first make sure the gas burner head is clean by scrubbing it with an old toothbrush and hot white vinegar. Then use a safety pin or small paper clip in the orifice hole to ensure it is clear. If these are good, make sure the spark is white or blue since, if the spark is yellow, orange, or red, it has a hard time lighting the gas. If it is yellow, orange, or red you will need to disassemble the main top to clean the connection points of the metal panels making up the main top. This may need to be done with sandpaper to re-establish ground to the surface burner for a strong spark. Read More...
Lori October 25, 2019 for Model Number NGM5664UC/03 Good morning, one of my burners, the one that gets used to most, will not light. There is clicking and a spark and you can smell gas, but the burner will not light. Wondering which part will fix the issue. Any help would be appreciated. Thank you!
1 Answer Hello Lori, you did not mention which burner was having the problem, so we will go with a general checks, first remove the burner cap and check the ports on the burner base and make sure all are clean, then check down thru the center port and check the orifice is not blocked with any debris, check underside of cap for any irregularities, reinstall the cap correctly ,check the spark ignitor has a clean /strong spark, if still having a problem lighting then replace the burner base and cap. Read More...
Gene September 12, 2019 for Model Number NGM8054UC/03 Hello, I want to make sure I am buying the right part for the problem. My most used burner does not always light up. It takes 2-3 tries of sometimes prolonged clicking. It does eventually light up. I lights up with a match and the flow seems to be fine. The rest of the burners work fine. Also, I cleaned up the burner extensively, which helped a little bit. Is it igniter?
1 Answer Gene, Most likely it is the igniter. If these igniters fracture it will arch away from the burner instead of into the burner base resulting in a long wait before it will light. Read More...
Stephen On April 06, 2019 for Model Number BOSCH Gas Cooktops NGM8654uc/02 Try to replace BOSCH IGNITION DEVICE (00612817) To remove the brass nut in the center of the burner, which direction should I turn to loose the nut? Thanks.
1 Answer IgnitorClicking, The 00612817 / 00612817 Ignition Device, is for a single (one/1) ignitor part. The part is in stock and available at this time. Thanks, Read More...
Sharon S October 01, 2017 for Model Number NGM5064UC/01 The ignitor keeps clicking even after the burn has been lit. Does this mean the ignitor needs to be replaced or is there another problem?
1 Answer Hello Sharon. You will need to clean all the burner and make sure they are not wet. If not, then the spark switch is bad and will need to be replaced on the unit. Thanks. Read More...
Sharon October 01, 2017 for Model Number NGM5064UC/01 Bosch Gas Countertop The ignitors on the right side continue to click after the burner is lit. Does this mean I need a new ignitor? It is clean and everything looks good but just keeps ticking.
1 Answer Hello Sharon. The flame needs to make the ground. If it is, then the spark switches will need to be checked to see if they are bad. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...