Norton May 14, 2014 for Model Number Decor oven model #cpo130w serial # 207117 The oven failure code is F1. Would the replacement part Control Board Erc# 62692 work in our oven. Thank you for your reply.
1 Answer Hello Norton, The F1 code is a shorted heater element relay circuit on your control board. You will need to contact corecentricsolutions.com to see if they support mfg. part number 82837 82837. If so, since it is no longer available, you will need to ship it to them for repair. Otherwise, I'm sorry, but this part has been discontinued and the manufacturer has listed no satisfactory substitution. Read More...
Frank R. May 10, 2014 for Model Number cps130 built in wall oven serial #vd7340690 We have a Dacor wall oven that we can't read the numbers to set time or temperature.
1 Answer Hello Frank, The only way to correct this issue is to replace the oven control board. Read More...
Dan March 23, 2014 for Model Number ECS127 I have a Dacor ECS127 and the display is out and the only button that works is the light. I tried cycling the circuit breaker and the wire harnesses to the controller with no change. Is there anything else worth trying? Is this a broken controller or a broken relay board? Thanks, Dan
1 Answer Hello Dan, The thermal switch DE81-04971A could be tripped, (resettable), or the control DE81-07990A has failed. Read More...
Dan March 23, 2014 for Model Number ECS127 I have a Dacor ECS127 and the front display is not longer working nor are any buttons except the light. The oven has power but nothing else seems working. I recently replaced the switch membrane to fix and issue with the temperature shooting up when you turn the oven on. That was all working fine. Any suggestions?
1 Answer Dan, Based on the information it sounds like the issue with the unit will be a faulty oven control. The part number for the oven control is 62692. Read More...
Leslie February 09, 2014 for Model Number Dacor wall oven model ECD230SCH V-G-03123198 The bottom bake element in my top wall oven will not come on. We just replaced the bake element and it still will not work. There are no errors messages on the panel when we turn it on and let it run. The oven does warm some from the preheat functions that work (convection, broiler) I've tested the bottom back element and it's not on at all. From day one, the sensor probe in this oven has not worked properly, but we just don't use it. If you try to use the probe it gives you error messages. The ovens are ten years old.
1 Answer Leslie, The most likely issue since the bake element has been replaced but still not functioning would be a faulty relay board DE81-08448A for the bake and broil. Read More...
Kris W. January 10, 2014 for Model Number MCS130S I am looking for the oven sensor for a 30" Dacor wall oven model #MCS130S purchased in 2003. Serial #V-F-02463444. Thanks.
Kris Woodard December 13, 2013 for Model Number MCS130S I have a 30" wall oven model #MCS130S purchased in 2003. Serial #V-F-02463444. I need to purchase a new motherboard for this stove. The existing motherboard is Dacor #62694. Are these still avialable? Thanks Kris Woodard
1 Answer Kris, Yes the control board for your unit DE81-07990A is still showing that the part has not been discontinued at this time. Read More...
Jerry C October 28, 2013 for Model Number DACOR E0130SCH Hi, My Dacor oven isn't working, and the control board post an error message U43, I know it means upper over / relay board, I have a built in single oven / microwave / conventional oven. What relay board OEM part # will I need for my DACOR E0130SCH serial # V-D-06500011? and are they an easy DIY project? Thank you, Jerry Corrales
1 Answer Jerry, The relay board that you would need for your wall oven is part number DE81-09742A. Read More...
Todd October 22, 2013 for Model Number cps 1306 Our oven has an overachiever problem. Once the broiler element turns on, it will not turn off until the circuit breaker is turned off or the overtemp sensor shuts down the oven. I'm guessing the 62692 control board is my fix but any other ideas? Thanks
Nc412 June 07, 2013 for Model Number CPS130 My oven won't work. When I select any of the oven choices, i.e, bake, convection, pure convection, it allows me to enter a temperature (350 degrees for example), it goes to preheat but after several seconds it shuts itself off. The clock works but is slowly losing time and the timer works okay. Can you advise as to what the problem is and the solution? Thanks!
1 Answer NC412, The issue with the unit shutting down a couple seconds after set to preheat and losing time then the control board 62692 is faulty and need to be replaced. Read More...