Crystal July 04, 2021 for Model Number Affinity Front loader - The first 3 or 4 numbers are partially faded but I believe it is FAFW3511KWO The washer stopped in mid cycle?? (was not watching) The clothes were sopping wet. We emptied the coin catcher and re assembled. Tested the error buttons, tried to reset. The machine will go through partial cycles, but never spin fast or empty the water. The door appears to be closing/latching good. Is is the control panel? The machine is about 9 years old???Please advise if 1) We should buy new 2) have a tech come in or 3) you know what I need. TY!!!
1 Answer Crystal, if no error codes show when pressing and holding the start and cancel buttons at the same time, the failure would likely be in the main control 137006060. Read More...
Denise January 08, 2021 for Model Number LAFW3511KB0 error code E90 elect panel control board . please confirm the correct part # . or cross ref part # . on the diagram it seems to be #1 but please confirm
1 Answer Denise, the electric panel control is going to be the user control 137006060 for this model. Read More...
1 Answer Hello Ann. Measure the voltage between the black wire in the J2 connector on the console control board and ground. If you read 120 VAC, replace the console control board. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Tim January 07, 2017 I have a Frigidaire affinity dryer I changed the heating element a few years back but recently it started showing a code e64, now it has started showing e61 code not sure what part I need or what the problem is ?
1 Answer Tim, The E61 error code indicates a problem with the heater relay or wiring on the control board. The E64 error code indicates the problem is in the heater element or wiring (again). Wander if a wire or the element shorted out and caused the relay contacts to stick or short together, you'll need to inspect and check both components.. Read More...
Joe September 01, 2015 for Model Number fafw3511kbo Washer will not spin. After entering test mode pulled an F 43 code. There are 3 boards. Tech sheet says to replace the console board. The parts list does not specifically name wich board is the console board. Can you tell me which board is the console board?
Ted August 12, 2015 for Model Number fafw3511kwo Is e41 code a control board issue? I did run a test on the door latch by disconnecting it and reconnect, but was not successful.
1 Answer Hello Ted. Control board thinks the door switch is open. You will need to replace the door lock on the unit. Read More...
Paul September 11, 2013 for Model Number FAFW3511KRO Just finished installing a new control board. I have power at the connection to the board, but nothing, no lights nothing. What next? and can I return the board if that's not the problem?
1 Answer Paul, If you have power going into the control board and there are no lights coming on when the unit is plugged up and turned on then the control board is faulty. Since this is an all inclusive board in which the lights are part of the main board. Read More...
Paul September 09, 2013 for Model Number Frigidaire FAFW3511KRO Washer stopeed working in the middle of wash cycle. No lights no sounds no power. Breaker not tripped outlet good. Would this be the control board?
1 Answer Hello Paul. If there is power to the control board and it does not work, you will need to replace the control board on the unit. Read More...
Eric July 18, 2013 for Model Number FAFW3511KW0 Error code E43 Went through diagnostic sequence and everything functioned properly until test#7. According to the data sheet the control board is defective...Is this a sure thing?
1 Answer Hello Eric. Based on the test you did, yes you need to replace the board in the unit. Read More...
Savatage October 27, 2012 for Model Number FAFW3511KR0 Getting flashing light and finally got it to display error code E62. Would this be a faulty control board?
1 Answer Hello Savatage, The first thing you should do is check your incoming voltage for you wall plug in. Check to make sure you are only getting 120vac. If you are getting 120vac then you will need to replace main control board 137006060, as there is no designation for E62 error code. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...