Jared December 11, 2016 for Model Number FGHS2344KF1 The refrigerator temperature display reads 99 but the food in the refrigerator will freeze. The temperature display for the freezer reads -9 but is set at 4 degrees. What is the problem or what part do i need to replace?
1 Answer Jared, You will want to test the thermistors in the unit to make sure that they are good. The thermistor should have a resistance of 5K ohms of resistance at room temperature of 77 degrees. If the resistance is incorrect then they will need replaced. If they check ok then the control board would be the issue. Read More...
Amber October 12, 2016 for Model Number frigedare gallery My ice maker door pops open but no ice comes out? Could this be the control panel?
1 Answer Hello Amber. You will need to test for power to the auger motor. If there and it does not run, you will need to replace the auger motor on the unit. Read More...
George N September 10, 2016 for Model Number LGHS2634KPO I have a ice maker problem , done all trouble shooting items , after all done noticed temp on control board for both frez----ref seem wrong set at 5 and 37 both reading higher than what called for frez at times goes to 20 but in side is ok same with the frig side could it be a bad control board and all so causeing the ice maker not to work
1 Answer George, Yes it is possible that the issue with the icemaker could be caused by the control board on the unit. Also keep in mind that if the unit is not getting cold enough it will cause the icemaker to not cycle. Read More...
Buddy L March 06, 2016 for Model Number lgub2642lf4 The ice despencer will not switch from cubes to crushed ice. Changed solenoid that shifts the ice maker from cube to crushed ice, and no voltages 120v to solenoid. What could be the problem?
1 Answer Hello Buddy. It sounds like the control board 242115279 is bad. Sorry, but this part has been permanently discontinued by the manufacturer and we don't know of any source or replacement for the part. Thank you. Read More...
John K January 06, 2016 for Model Number FGHS2644KF1 I got the sy ce error code. Replaced main control under the fridge; and it didn't work. Ordered another; it doesn't work. Ordered the digital control panel for the front to compliment the main control; still doesn't work. Any ideas before I give in to returning the parts and buying a new refrigerator? Thanks
1 Answer Hello John. If you have replaced both boards and still get the error, you have an issue with the wiring on the unit. Check all connectors and wires for continuity. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Art October 08, 2015 Does the control board control ice maker fill? The water in door works, the valve is okay and the area is cold enough.
1 Answer Art, The icemaker itself is what calls for the icemaker to call for water. The dispenser dispensing water would have no effect on the icemaker as there are 2 different solenoids. What you want to check for is to make sure that the fill tube is not frozen, and check to see if there is power to the icemaker water solenoid when the unit is calling for water to the icemaker. No power bad icemaker, if there is power then bad water valve. Read More...
Karl September 22, 2015 for Model Number FFSC2323LS6 My refrigerator is in a RV ,It is residential and only runs on house current ,The problem is the control panel on the ice maker door reads different tempatures all the time ,sometimes -20 the freezer seems to work fine as far as getting cold ,but the refrigerator barely gets cold .and like I said but read abnormal tempatures ,any idea?
1 Answer Hello Carl. With the readings being wrong, and changing, it sounds like the control board 5303918637 is bad and will need to be replaced on the unit. Read More...
Robert G. June 03, 2015 for Model Number LGHC2342LF3 I am having trouble with the ice dispenser. The auger motor will not turn and now after replacing the auger motor, I noticed the ice door pops open but won't stay open. The auger motor still is not working even with a new one in there so its not getting power. I am thinking it must be one of the control boards. Which part do I need?
1 Answer Hello Robert, You should first verify the connections at the door hinge and in the control area. This can be caused by either the actuating switch, 242074218, or the control board 241973711. Read More...
Damien T October 27, 2014 for Model Number lgub2642lf3 Frigidaire Gallery Hi, my Frigidaire gallery recently stopped working all together. No lights show up on the ice dispenser or even the inside when I open the door. When I took a thorough look in the fridge I noticed some sensor got tangled and broke in the ice machine auger. What do you think? Thank you.
1 Answer Hello Damien. Repair the sensor and wire. If the unit does not come back on, then check the main power board 242115279 on the unit. Read More...
Dan October 05, 2014 for Model Number FGHB2844LF6 I have had tons of problems with the ice maker thawing and not creating ice. I went to get a glass of ice and the turbine got stuck making a horrible noise and then the refrigerator turned off. I tried to pull the tray out like I have countless times and it was stuck. Could not pull the tray out. A rubber hose surrounding some wires had been pulled in the the tray and got stuck around the turbine. I have verified the wall socket is hot. I tried to find the reset button on the back electrical panel to try that but nothing. I let it sit for 4 hours hoping a capacitor would get discharged. No luck. I am thinking it is the control board but how can I verify that? Thanks
1 Answer Hello Dan, You will need to replace the icemaker assembly 243297613. The auger motor should be heated with a hair dryer for at least 15 minutes to verify it is not frozen. If this makes it operate, check for air leaks allowing humidity to enter the unit. There is the possibility that the control board could have an issue but that would not be the result of the thermistor getting into the auger. Read More...