Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Refrigerator Dispenser Control Board by Frigidaire

Best Seller
Manufacturer Part
4.89 (64)
By: Frigidaire
Part Number: OEM15974217
Manufacturer Part Number: 241973711

Fix ice/water dispenser not working or SY CE error code. This dispenser control board restores ice and water selection. Moderate DIY repair, 1-2 hours.

More
$212.95

IN STOCK
Ships Today Guaranteed
Add to Cart

Questions & Answers

For Frigidaire Refrigerator Dispenser Control Board (Part Number: OEM15974217)

1 Answer

Hello Jace,
You will need to make sure the harness is not damaged and connected properly at the door hinge. If no problems are located, the issue is most likely the mainboard 5304499076 under the unit behind the kick panel.

Read More...

1 Answer

Vo,

You will want to remove the drip tray from the dispenser and there will be a screw that you will remove. Once removed you will want to pull out on the dispenser trim and this will allow you to gain access to the control board.

Read More...

1 Answer

Rhonda,

The SY CE error code would be a communication issue between the main board and the dispenser control board. This will most likely be the dispenser control that is needing to be replaced.

Read More...
Alex for Model Number Fridgidaire FPHS2386LF6

My fridge doesn't have any lights on control panel above ice dispenser. Freezer internal light is working and it freezing good. Fridge inside light doesn't work but the food is cool. I know for sure the bulb is fine because once in a few weeks everything comes back for a few minutes. Before control panel lights stopped working temperature adjustment buttons and some other buttons weren't working all the time. I am suspecting it's faulty control board (part number 241973702) behind touch buttons panel. Looks like part # 241973702 was discontinued and replaced with 241973711. Am I right? Do you think it will fix it by swapping it with 241973711.

1 Answer

Alex,

With the issue of the control on the dispenser and the lights not working then this issue will most likely be caused by a faulty main control board which is part number 5303918525

Read More...
Michael for Model Number FGHC2342LF3

The control panel on my refrigerator seems to be locked. None of the buttons respond to touch. The refrigerator temp indicates 38 degrees and the freezer temp indicates zero degrees. I have unplugged the refrigerator several times (30 seconds, and once for 30 minutes) in an attempt to reset the control panel but it is still locked. The refrigerator beeps once after I plug it back in but none of the buttons will function. Is my control board faulty?

1 Answer

Hello Michael. You will need to try to hold down on the control lock button on the left bottom corner to see if the control panel will unlock. If not, and no buttons work, you will need to replace the switch assembly 242167017 if the ribbon cables are installed properly. Thank you.

Read More...

1 Answer

Scott,

There is a button in the center of the temperature displays that says C/F, if you push that it should switch back to Fahrenheit.

Read More...

1 Answer

Hello Lennie. You will need to remove the trim on the freezer door to access and replace the board. Make sure the unit is unplugged. When removing the freezer door trim to access the display board, use a thin plastic scraper to pry the trim out until the trim comes loose. Once the trim is removed you can remove the board and replace it.

Read More...

1 Answer

Hello Matt. You will need to check and see if the damper 241853801 is bad on the unit and will need to be replaced. If the door is broke, it will cause the unit to freezer things inside the fresh food compartment.

Read More...
Ralph N for Model Number dghf2360pf7a

I have a Frigidaire refrig dghf2360pf7A with variable speed compressor the compressor will not run everything else works I did the diagnostic test on main board to see if correct ac voltage and dc voltage was going to compressor inverter board the service data sheet said it should be 10-15 vac 1-5 vdc I was not getting the correct voltage to inverter. I am getting 2.78 ac volts and 9.8 dc volts I got a new main board but still getting wrong voltage. I used the system diagnostic mode to make compressor run it still would not run. everything else works. what you think?

1 Answer

Ralph,

Check at the main board to see if there is proper power. If there is proper power then the issue will be in the wiring and will need to determine where you are dropping voltage at.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google