Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Refrigerator Freezer Electronic Control Board (White) by Frigidaire

Best Seller
Manufacturer Part
4.89 (64)
By: Frigidaire
Part Number: OEM15956754
Manufacturer Part Number: 297370600

This electronic control board includes the user-facing touch pad display panel and the circuit board that manages freezer temperature settings and functions. It mounts on the exterior of the freezer compartment and allows you to adjust temperature and other settings. Replace this board if the display is blank, unresponsive, shows error codes, or if the freezer is not maintaining the correct temperature despite other components working properly.

More
$118.95

IN STOCK
Ships Today Guaranteed
Add to Cart

Questions & Answers

For Frigidaire Refrigerator Freezer Electronic Control Board (White) (Part Number: OEM15956754)

1 Answer

Hello Jerome,
This fault code indicates that there is that a problem exists with the temperature sensor. The sensor 297018400 will need to be replaced to fix this issue. If the problem persists and there is no harness issue, the control 297370600 will need to be replaced.

Read More...

1 Answer

Bluesgene, The "EZ Set" Control 297370600 / 297241800 doesn't have any error codes (b.). Based on your post description, you will need to replace the control assembly. Make sure you remove power to the freezer , and be careful removing the control from the door, try not to scratch or dent the door panel when you pry the control out of the opening.

Read More...

1 Answer

Hello Tim. Based on the information you provided, you will need to order and replace the control board 297235200 on the unit. Thank you.

Read More...

1 Answer

Tom,

It would be recommended to remove the rear wall of the inner freezer and check the frost pattern on the evaporator coils. If the coils are impacted by ice then this will be a defrost issue and will want to test the defrost heater and defrost thermostat for continuity. If there is no continuity then this will be faulty and will need to replace the affected part. If both have continuity then this issue will most likely be caused by a faulty control board 297370600.

Read More...
Michelle for Model Number FFU14F5HWB

I have a Frigidaire upright freezer Model #FFU14F5HWB Freezer "Hi Temp" is on and only blows warm air.  Compressor is running from what I can see, it is hot and two of the copper pipes are hot and one is cold.  I have not heard the compressor click, but it seems to be working. Tested defrost thermostat, heater defrost, compressor and compressor controller with a digital clamp meter with the ohms beep setting and all passed with a beep. I can't find a how to test the User Control & Display.  Is there a way to test the User Control & Display?  Do you think that the User Control & Display is the problem? Thank you very much I truly appreciate your help.

1 Answer

Hello Michelle. If the compressor is running and the unit is not cooling, then you have sealed system failure and will need an HVAC tech to come out and repair the unit. Thank you.

Read More...

1 Answer

Hello Kent. If the control board did not match that model, you will need to order the correct board 297370600 for the unit. If there is no power coming to the compressor then it sounds like the board was incorrect for the unit. Thank you.

Read More...
David G for Model Number ffu17f5hwd

I looked at my freezer and the Hi Temp and Door Ajar lights were blinking and no number was in the display. The interior light was blinking. None of the buttons did anything and unplugging didn't help and the compressor wasn't running either. I went back out about 45 minutes later and the compressor was running and all the lights were out on the control panel, as was the interior light. None of the buttons do any thing and it appears the compressor runs all the time now. Prior to this happening, the HI Temp and Door Ajar lights would come on as soon as I opened the door an the control panel temp light would go to 8. Everything would restore when I closed the door. Bad Control Panel? BTW, the alarms aren't sounding either.

1 Answer

David, Check to make sure the outlet is a 120 VAC, grounded, polarized outlet, and the voltage is correct. Check the airing harness and connections at the door and behind the front kick plate grille. If all's OK, then replace the control 297370600 / 297241800 Control-electronic, assy, white, 115V .

Read More...

1 Answer

Hello Jack,
The control board 297370600 will be the cause of this issue. This is a common failure and it is impossible to say if the electrical work caused the issue or not.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google