1 Answer Hello Julie, thanks for reaching out to AppliancePartsPros.comIf only the start button isn't working and all the other buttons seem responsive, it is likely that the overlay insert 807327602 will need to be replaced. Read More...
Joe December 21, 2020 for Model Number Frigidaire__FGBD2445NF1A The drain pump is not working correct. It is leaving about an inch of water after the wash cycle is finished. Could this be a bad control board or is there something else I can check or test? I'm very knowledgeable with electronics and testing with a multimeter.
1 Answer Joe, if the water is above the filter 154283005 it would be recommended that the drain hose is inspected for any clogs. If the water is below the filter, it is normal operation for some water to be present in the bottom of the sump. However, the drain hose can be inspected for a partial clog and the drain pump A00126401 can be inspected for a loose impeller. Read More...
Mark March 19, 2019 for Model Number fgbd2451kf1 I have to replace the control board. How do you remove the control panel to access the card? Do I have to remove the entire front panel, or can the top cover be removed separately?
1 Answer Mark, you would need to remove the front panel and then the control panel. From there, there are 3 screws that will need to be removed from the control cover. This will give you access to change out the control. Read More...
Efrin September 25, 2018 for Model Number FGBD2432KB1 What should I press on the keypad to put the washer on the drain cycle? also would it go drain with out water in it(I took the water line out) or I need to put water in the washer.. Thanks again..
1 Answer Efrin, " You can cancel a cycle anytime during the cycle. Press START/CANCEL pad and the dishwasher will start a 90 second drain, then turn off ". No the dishwasher does not need to have water in the tub. Read More...
Efrin September 25, 2018 for Model Number Frigidaire__FGBD2432KB1 Where can I check for 120vac power to the drain pump. So I would know if there is power or not going to the the pump.. I want to monitor it with voltmeter on the draining.. Maybe the control board or the drain pump is bad... Thank you much...
1 Answer Efrin, The drain pump will have 2 wires going into it, you would put your meter leads in with the wires on the pump then run the drain to see if there is 120 vac to it. Read More...
John July 17, 2018 for Model Number frigidaire dgbd2432kf1 My Frigidaire dishwasher isn't drying the dishes recently. When i open the door during the drying cycle, its not very hot (usually is). I ran self diagnostics and it goes through all the cycles fine but leds stay on at end and when i open the door and close it, it flashes PF. I have continuity on the heating element and the high temp thermostat and visually look ok. Is this most likely the control board or is there anything else i can check. From what i can tell the dishes are still coming out clean.
1 Answer John, it sounds like you may be loosing power during the cycle to the heating circuit, get an volt reading from control board at pin P8, this is the red wire going to the element, you should get 120 volts when in dryng mode, if not replace the control board. Part number for the board is 807024601 Read More...
Danmcd June 12, 2017 for Model Number DGBD2432KF1 Dishwasher recently started getting build up of mildew, heater does not seem to be working. I replaced the element (before checking old one, which was reading ~14 ohms). I checked the hi-limit switch, reading 0 ohms. Wiring looks okay visually, all other functions seem to work fine. Is it likely a bad relay on the control board?
1 Answer Dan, With the heater not coming on then yes the relay on the control board would likely be the cause. The control board would need replaced for this issue. Read More...
David A. February 03, 2017 for Model Number FGBD2445NF1A Display does not come on. Green power light is on, but nothing else works. Will not fill and can make no option selections.
1 Answer Hello David, Since there are problems programming the units' cycle and the display is not operational, the control board 807024601 will need to be replaced if all connections prove good. Read More...
Todd December 29, 2016 for Model Number fgbd2451kf1 I have no power going to my drain pump. Is this controlled by the main control board. All of my other things work fine just no voltage too my drain pump.
1 Answer Hello Todd. Yes, if the wiring is all good on the unit then you will need to order and replace the main board on the unit. Read More...
Sarah December 31, 2015 for Model Number LGBD2432LW0A My dishwasher will not run the "normal wash" cycle, but "heavy wash" works perfectly fine. Does that sound like a problem with the control unit?
1 Answer Sarah, Yes, with the normal wash not working but will work on other loads then this will be a control board issue. Read More...