Payson July 05, 2017 for Model Number TEO356BFW1 My stove is a double oven model. Upper and lower ovens, with 4 burners. Is there a video to show how to efficiently open up the panel? Thanks.
1 Answer Payson, Unfortunately there would not be any information available on this unit to be able to assist with removing the panel. It does look like there would be a couple screws at the top and bottom of the control panel that you would remove to get the panel to come off. Read More...
Sharon May 23, 2017 for Model Number RB 131L (Serial # 20CF1124) Hello! I have a circa 1972 Frigidaire electric cooktop that is still cookin'. However, I need new nobs for it. Believe it or not :o) all the paint has "disappeared" from the knobs, making it hard to know what heat setting you're at. I assume there are universal knobs ... Thanks for your help!
1 Answer Sharon, There is a universal knob kit that would work for the unit and would be part number TJKN002. Read More...
David March 22, 2017 for Model Number Gibson CEC1S3DSAA I need the surface unit switch for the one large burner. I have three small burners and 1 large burner. My model does not seem to be on the list. Pretty basic ancient unit. Thanks for your help. I need the part number.
Luke October 04, 2016 for Model Number 790.96129409 Does this work for all burners on the stovetop including the larger or dual ones in the front? Or is this just for the smaller rear burners? Thanks. Stove is a Kenmore 790.96129409
1 Answer Luke, Here are the locations of the burner switches and their part number left front 316436001, left rear and right rear 316436000, and right front 316238201 which is the dual element. Read More...
Drew March 17, 2016 for Model Number REG533MD2 For switch kit 5303935086 the installation instructions state: "6. Place volt meter leads on L1 of the new switch and the P terminal of other switch mentioned in step 5. If you read 220 volts, you must reverse the wires at L1 and L2 of the new switch before installing the pilot wire to the P terminal of the new switch. My questions is if L1 and L2 wires are installed correctly what should the volt meter read? 120 volts?
1 Answer Larry, We would need to have the model number of the unit to properly assist. Although this issue would most likely be caused by a faulty infinite switch. Read More...
Bill April 05, 2015 for Model Number Gibson Stove Model CE40C4AFAA My aunt has a very very old model electric Gibson Stove. Both the small burner's only go on HOT. They will no longer adjust to Med or Low heat. I was wondering what replacement part I could purchase to replace the Switch. It is not the burner's. I have already tested those.
1 Answer Bill, the switch listed for your model is part number 5301311751 however, it has been discontinued and is no longer available. You can use universal switch part number W10900107. Thanks. Read More...
Frank M February 28, 2015 for Model Number 79046803992 When I connect the existing wires to the new double element replacement switch Lit # 903057-9010 according to the connections diagram that comes with the switch my element will not turn on. Since the new switch locations are not marked on the switch, I am unsure if I am connecting the existing wires correctly. Any help you can give will be appreciated. Thanks
1 Answer Frank, When hooking up the switch, if you hooked it up per the diagram that came with the part then it would be connected properly and most likely the element is bad. Read More...
Johnc February 09, 2015 for Model Number 13-3626-08 I have a Tappan 13-3626-08 stove top. It has 2 large burners and 2 smaller burners. The large burner switch says 8.9-10.8A (I assume AMPs). The small burner switch says 5.3-6.4A. Would your switch AP2591804 be a replacement for either of these switches? And if so, do you have a sister switch for the other? In case you want them, the large switch has these numbers on it: Type B 8411301 250V 8.9-10.8A 699T0117P03 QE214504. The small switch has these numbers on it. TYPE A 8712071 250V 5.3-6.4A 699T017P04 QE214503. Thanks, JohnC
1 Answer JohnC, the surface unit switch, part number 5303935086, is the correct replacement listed for your model and can be used as the small or large burner switch. Thanks. Read More...
Randy September 21, 2014 for Model Number frigidaire RG533HL2 I need a new switch for the left rear stove top element. The existing switches are Type A for the small element and Type B for the large elements. The Type B switch has numbers 8506251 and 1313767. Which replacement part do I need?
1 Answer Randy, the manufactured replacement infinite switch listed for your appliance is part number 5303935086. Thanks! Read More...