Myriam November 14, 2020 Hello I have a problem with my Kenmore brand washer. When I turn on my washer the water keeps flowing as if it no longer cut the water, both cold water and hot water as cold water now because the problem started with hot water. I was thinking of bying this part 134211400! Do you know if it's ok for my problem?
1 Answer Myriam, this could be a failure in the pressure sensor switch or a clog in the pressure hose. If the model number of your appliance could be provided in a new question, this will allow the most accurate information to be presented. Read More...
David October 15, 2018 for Model Number Frigidare washer/dryer combo FEX831CS0 The washer fills with water and then will not start the agitate cleaning cycle i can manually turn it to the end of the cycle and it will drain and spin. What part is not working properly that it will not initiate the cleaning cycle?
1 Answer David, Check between pins 14 and 21 on your timer when it should be agitating for 120 volts. If no voltage your timer needs replaced. Read More...
Mike September 22, 2018 On a Frigidaire stackable washer dryer Model FEX831CSO How do you remove the front panel on the washer to check out the pressure hose and switch. Our unit will not fill with water.
1 Answer Mike, There are 2 screws at the bottom of the panel that you will remove to roll the front panel out and off. This will give access to screws that hold the main top on that you can remove to access the pressure hose and switch. Read More...
Timothy Sandy June 05, 2018 for Model Number FEX831CS0 hello, tub will not fill with water on any water level setting. No water at all will come into tub. please help ty
1 Answer Hello Timothy, you'll want to test for voltage at the water valve when it should be filling with water. If you have voltage present you'll want to make sure the water is turned on before replacing the water valve. If no voltage present you'll want to verify the pressure tube and air dome are free from any obstructions before replacing the pressure switch. Thanks! Read More...
Kevin September 09, 2016 for Model Number 110.28022011 I am replacing a pressure switch on a washer / dryer combo stack Kenmore. I disconnected the wires to the pressure switch and now cant remember where they go. I have looked on line and have had no luck.I tried guessing but it sparked and blew a breaker, afraid to guess again ! my part number is 121692000 wire colors are Red white with black stripe white or cream color I can not find a schematic on the machine anywhere. any help would be appreciated.Thank you in advance
1 Answer Hello Kevin. The model number will have to be verified on the units I.D. tag since the one listed came up invalid. This will be necessary to look up and specific parts such as the one you requested. Thank you for your patience and understanding in this matter. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Woody October 29, 2015 I have a Frigidaire washer dryer combo model FEX831CS0, It will work and run fine when the low water selector is selected, but if selecting the medium or high water setting it will fill with water but stop and the timer dial never moves.
1 Answer Hello Woody, If there is not a lint buildup in the outer tub assembly that could be blocking the pressure switch hose, the most probable cause of this issue is the pressure switch 134422700. Read More...
Emma August 21, 2015 for Model Number FGX831CS1 Need esactly parts of the switch to my machine Frigidaire FGX831CS1 reference, it must be 3/4 ", since it already tested in 1", it did not work
Jack G. September 06, 2014 for Model Number Frigidaire Laundry center model #FGX831FS3 My Mother-in-Law's laundry center washer will not final spin or drain. The unit will fill with the lid up and agitate once the lid is down. So I don't think its the safety switch. I have replaced the drain motor and the washer timer. These changes have made no difference. It still won't spin or drain. What could the problem be?
1 Answer Hello Jack, The most common issues with this design is the lid lock/switch assembly 134101800 and the drain pump 137221600. Read More...
Bernie August 05, 2014 for Model Number Model #FLXE52RBS8 The dryer will not start, no humming, buzzing or anything when you push the start button on a dry setting. The lower washing machine works well. Hope you can help with a diagnosis! THANK YOU!
1 Answer Hello Bernie. Check the door switch and the thermal fuse 134120900 in the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Elizabeth November 21, 2013 for Model Number glgt1031fs0 When you turn the timer knob to select a time/type of dryer setting, and then turn the knob to start. The dryer starts but the timer never turns it stays in the same starting position and it heat never gets hot?
1 Answer Hello Elizabeth. The no heat can prevent the timer from turning. Check and make sure you have 240 volts coming to the dryer. Check and make sure the unit is not set to Air Fluff. Also check the heater and thermostats and see if they are good. You can test these with a multi-meter MA-DM1. They should read closed for continuity. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...