Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This kit includes the splutch pulley and cam assembly used in the washer's drive system to engage the spin and agitate modes. The splutch mechanism sits beneath the outer tub and works with the drive motor to switch between washing and spinning cycles. Replace this kit if the washer fails to agitate, won't spin, or makes grinding or clicking noises during operation.
Replaced washer drive block and Cam. I called around and finally settled on Appliance Parts Pros because they helped diagnose the problem, told me what parts to replace and had videos to show me how to do it. In completing the repair I had to remove quite a few pieces of hardware in order to get at the part I was to replace. The videos helped but there is a learning curve while you familiarize yourself with the parts and figure out how the remove them. Eventually I got to a large nut that,... Read more
The Drive Hub Kit is an OEM replacement part for Whirlpool washers. This kit includes an important transmission component - the drive hub - along with mounting hardware. The drive hub transfers power from the washer motor to turn the wash basket and agitate laundry.
Symptoms of a bad drive hub can include:
Causes of a bad drive hub include normal wear over time, strain from heavy or unbalanced loads, or damage from impact or other external forces.
This OEM replacement kit is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
I watched a video on YouTube that showed my exact problem. It had a link to this part AP5665171 Hub and it showed how to fix it. It was a fairly simple fix. I did not even have to remove the tub. I popped the cap on top of the agitator plate (AGP), removed the bolt hold the AGP on. I tapped on the bolt several time to loosen it. Using an angled screw driver, carefully and slowly lifted up the edges of the AGP until I could use my fingers to carefully pull the AGP off the splined drive... Read more
The washer drive belt transfers motor power to the washer’s drive system so the basket spins and agitates. Replacing a stretched or broken belt helps stop squealing and slipping so cycles finish at proper spin speed.
What it does
What’s included One drive belt.
Install notes
This OEM Whirlpool belt is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models.
This was my first attempt, ever, to repair a washing machine. After some internet research on the problems, I was able to determine that the shaft seal on the gearcase probably was leaking water into the gearcase with each use. No water was ever found on the floor, but when I turned the washer over to inspect the gearcase, I found a black, oily residue on the outside of it along with the same residue on the pulleys, the belt and the motor. I ordered a new gearcase, shift actuator, splutch... Read more
Lid won't lock or keeps clicking? This washer lid latch assembly fixes locking failures. DIY-friendly repair with video guide, typically done in 30-45 minutes.
Not wanting to spend hundreds of dollars on an appliance technician's service call, I searched online to troubleshoot the problems with my particular Maytag Washer Model Number MVWX500BW0. I stumbled across AppliancePartsPros.com and investigated there the most likely causes for my Maytag Washer's not agitating properly and not spinning at all. In order to acquire some additional information, I telephoned AppliancePartsPros.com and spoke with an extremely professional, knowledgeable and helpful... Read more
Fix a washer that won't spin, agitate, or shows F7-E1/F7-E7 errors with a new shift actuator. Controls cycle transitions. Easy DIY repair with video guide.
Repairs loud roaring or grinding noises during spin cycle. Replace when bearings rust or seals leak water. Confirm fit with your washer model number.
After about 6 months of use with our Whirlpool Cabrio washing machine it started to sound extremely loud in the spin cycle, we should have called Whirlpool at this point to have it looked at under warranty. Fast forward 5 years later our loud washing machine ended up leaking out the bottom, we had a local service company come out to take a look at doing the repair and they quoted $800 to replace the outer tub assembly. I was not going to pay $800 and figured that most likely we would purchase a... Read more
Four-rod suspension kit that supports the washer tub assembly. Replace when rods are worn, stretched, or causing excessive vibration during spin cycles.
I called a repair guy who came out to specifically replace the suspension rods because I read that if you push down on the tub and it bounces around, then the rods have worn out. After running the diagnostics, the repair guy tried to tell me it was because the lid was not locking correctly! After expressing concern that this makes no sense, he continued taking things apart and noticed the agitator rollers were all broken and told me this is probably causing the tub to be unbalanced. I... Read more
Fixes loud roaring noise during spin cycle or basket wobbling. Connects basket to drive shaft for smooth spinning. Moderate DIY repair with video.
After ignoring for a couple of years that the bearings were bad on our Whirlpool Cabrio washer and just closing the door to the laundry room, it started slinging grease underneath during the spin cycle. Knowing that the cost to call out a repairman would be close to the cost of a new washer, I decided that it would be a nice Saturday project after reviewing AppliancePartsPros’ repair video. The bearing & tub seal kit and bearing installation tool arrived in two days. I’ve done a lot of... Read more
Suspension bearing kit supports the tub assembly in top-load washers. Replace if bearings are worn, cracked, or causing excessive tub movement or noise.
After looking up the model number of my washing machine on AppliancePartsPros.com I ordered the suspension rod kit, two sets of tub centering springs (one spring per corner), a Ring-Tub (mine was breaking apart due to banging around) and a spare suspension bearing kit in case I need it later. I spoke to a very helpful customer service rep on the phone just before placing my order. They have customer service representatives answering the phone late at night. I was surprised. All of my parts were... Read more
Replacement tub centering springs for washers. Maintains proper tub alignment and positioning within the cabinet. Replace if springs are missing or broken.
Fix an agitator that won't turn or leaks fabric softener with this inner cap. Simple 5-minute repair—remove the outer cap and replace. Video guide included.
I had replaced the Agitator cams a couple of times already due to my brother-in-law overloading the machine which stripped the teeth off of the cams. I also noticed the agitator seemed to 'wobble' and made 'knocking' noises quite a bit. I reviewed the video on the Appliance Parts Pros web site, disassembled the agitator and cleaned everything up, which helped a little, but not enough. Figuring the agitator itself was worn out also, I looked up and ordered all the parts for the upper agitator on... Read more
Rubber washer that seals beneath the agitator bolt to secure the agitator to the drive shaft. Replace if agitator loosens or leaks occur. Verify fit.
I replaced the washer plate and new screw/washer part. Easy fix and back up and running in ubder 10 minutes. Read more
Loud grinding noise during spin cycle? Failed gearcase bearings cause noise and oil leaks. Moderately difficult repair requires disassembly and cleanup.
Disassembled washer and replaced gearcase and reassembled. Read more
Secures the washplate to the drive shaft in your washer. Replace if stripped, damaged, or missing during washplate repairs or agitator service.
If your washer won't drain or spins but leaves water in the tub, the drain pump likely failed. Most DIYers complete this repair in 20-30 minutes.
It was a fast fix. its a Maytag Centennial Top load washer. it took me about 20mins to remove the pump and instal the new one.Most of the time was spent moving the washer. Read more
Washer leaking underneath or won't drain? This drain pump expels water at cycle end. Common cause: coins jamming impeller. DIY-friendly repair.
Looked up the part on your website, ordered it, it came in the next day, watched the install video that you provided, installed it in a few minutes, happy wife! Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.