Eze May 04, 2016 for Model Number 41729042992 How to remove a 131800500 timer switch on a Kenmore washer?
1 Answer Hello Eze. To replace you would need to remove the timer knob by unscrewing it. Remove the main top by removing 2 or 3 screws from the back of the unit. Once the main top is removed you would then be able to access the timer to remove it. Read More...
Paul December 19, 2015 for Model Number 417-39012891 How do you remove the timer knob. Have already removed the washer's top.
1 Answer Paul, All the knobs except the timer knob pull off. To remove the timer knob, push the knob in and turn the knob counter clockwise(to the left) Then pull the timer dial/bezel off the timer shaft, dismount the timer (two screws) and reverse the procedure to install the timer. . Read More...
1 Answer Hello John. The model number will have to be verified on the units I.D. tag since the one listed came up invalid. This will be necessary to look up and specific parts such as the one you requested. Thank you for your patience and understanding in this matter.We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. Here is a link to help you locate it. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
1 Answer Hello Gehad. To replace you would need to remove the timer knob by unscrewing it. Remove the main top by removing 2 or 3 screws from the back of the unit. Once the main top is removed you would then be able to access the timer to remove. Read More...
Kevin September 15, 2014 for Model Number Frigidaire Washer Model FWT449GFS2 Over the past couple years I've replaced the Motor, Control Board, and the other day the drain pump. Drum was not draining due to a broken part on the pump. worked fine but would go into final spin. Read some older posts on a forum and bought a new door lock assembly. prior to installing, the machine stopped spinning all together. replaced the assembly and still no spin. The drum still fills and drains fine. I can hear clicking and the timer is moving, but still no spin. Any ideas?
1 Answer Hello Kevin. If the unit is draining and the lock is new, it sounds like a motor issue with the unit. You will need to check and see if the motor is bad. Read More...
Michael August 25, 2014 for Model Number Fridgidaire Gallery Washer The washer no longer agitates the wash but still spins to drain the water.
1 Answer Hello Michael. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
James December 20, 2013 for Model Number 417.39012890 Frigidaire M 417.39012890 front load washer. 15 years old. Did two normal loads. Third timer selector did not advance. Turned off and moved to drain, had to repeat for spin and then syphon remaining water out. Tried a fourth load with same non-advance results just to double check. If its the timer unit can I get at it from the top? Does new unit come w instructions?
1 Answer James, This issue does sound like a timer issue. To replace you would need to remove the timer knob by unscrewing it. Remove the main top by removing 2 or 3 screws from the back of the unit. Once the main top is removed you would then be able to access the timer to remove. Read More...
Mark October 04, 2013 for Model Number fwt647 fridgidaire front load washer We loaded our washer and turned in on normal wash. The washer begins to fill but it doesn't begin to rotate the drum to distribute the initial fill. I manually turned the dial to spin after the water had filled the drum and it wont spin. I manually turned it to where it pumps out the water and that worked. So it seems as if the drum will not turn. Do you know where I begin to test for the weak link in the system, i.e the motor or the circuit board? FYI our home was flooded out in april, i had the washer unplugged as it was submerged. following a 3 month drying out process i powered it on and it worked like a charm for 4 months until now. Yes the motor and the circuit board at the bottom were submerged. the water didn't go much higher than the door switch. Any help would be good.
1 Answer Hello Mark. Test for power to the motor. If none is the the motor control board is bad. First make sure the belt is not broken on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Robert W. September 22, 2012 for Model Number FTW449GFS1 After opening my washer I heard and smelt a electrical wire burning. I couldn't tell where it was. I tried replacing the motor but it was not that. Can I have a better way of diagnosing my issiue?
1 Answer Hi Robert. The first thing to do is to verify the house outlet is OK. Use a volt/ohm meter part # MA-DM1 to assist you in your diagnostics. NOTE : The wide outlet terminal is the neutral (White wire side) and should not have any voltage to ground (The round -middle terminal). The narrow terminal is the " Hot" 120 vac supply and should have this voltage as you check from it to the neutral and the ground terminal respectively. If there is no voltage to ground then you need an electrician repair this. Remove the back cover off from the control board. Look inside the back and see if the smell comes from inside it. A burn smell usually follows the evidence of a burnt part.It will be advantageous to find the supplied tech sheet inside the cabinet to aid you in the diagnosis. It allows you to put the unit in a diagnostic mode which brings up fault codes and tells you which circuit needs assistance. Follow the power cord inside the unit and make sure the connections are tight. Does the tub spin freely ? Is there anything in between the tub and outer tub stopping the tub or the bearing seized? The speed control (motor control) is mounted inside the bottom of the unit. See if the control has opened a soldered fuse or the board circuit part # 131725300. Look at the Door latch part # 131763256 and see if the smell comes from it. You can remove the tub boot front clamp (hidden under the front lip), Fold the front half of the door boot inside the boot itself to allow you to put your hand inside the unit front and handle the door latch. Unbolt the latch front screws and pull the latch out to the side to see if it has internally burnt. The diagnostics sheet gives all devices resistance values to check one by one. See if the pump part # 137108000 has debris inside... Thank You. Read More...
Betty June 11, 2012 for Model Number gwt445rgs0 My Gibson washer (gwt445rgs0)fills with water, but then it doesn't agitate. It does drain and spin. Is this a timer problem?
1 Answer Hello Betty, This sounds more like a pressure switch 134433701 issue. The pressure switch is responsible for sending the signal back to the control when it is full so the control can continue through its' cycle. Read More...