Bill May 10, 2012 for Model Number FWT449GFS2 Washer was having intermittant problem going into high speed spin. Service technician checked pump and found some coins and other stuff which he cleaned out. Problem would not present while he was there (it never does!), so we assumed he had found and fixed it. However the problem quickly started reoccuring and is now no longer intermittant. Since we now know that the pump is in good shape and there are no obstructions, could this have to do with the water sensor or are there any other interlocks we should be aware of, or is this likely timer related?
1 Answer Hello Bill. If the pump is good, and the water is draining, but won't spin, the door lock assembly 131763256 may be the issue and will need to be replaced. Even if it locks, it may not send signal to the board, and thus will not spin out. Read More...
Jim M. April 15, 2012 for Model Number 41729042991 The machine cycles through all the phases but the length of time went from about an hour to more than one and a half hours. I replaced the timer with a new one but the length of time to complete the wash hasn't changed it's still 1 1/2 hrs. Do you have any suggestions as to what the cause could be. Thanks.
1 Answer Hi Jim. Immediately to the left of the timer is a speed control part # [131716900]. I would use a volt/ohm meter part # MA-DM1 to assist. you in your diagnosis. This may be either selected to a slower speed or internally shorted so it only works one speed. Open the bottom of the control panel. Use a shop vac to clean the water in the pump. The pump intake hose has a filter cup that catches the wash basket debris. Make sure that the pump impeller is solid on the shaft and not spinning loose. The pump has to drain completely then the spin speed will be met. Pump part # 137108000. Make sure the inlet valve screens are not clogged slowing the fill time. Flush out the hose's and screens also. Remove the top back 3-torx screws, push back on the top and lift up. Remove the 3/8" hose connected to the pressure switch and blow back in towards the tub. Did you remove any lint, debris or suds ? All will slow down production. Use Affresh tablets to insure the unit is cleaned monthly part # W10501250. Thank You. Read More...
Squash September 06, 2011 for Model Number 417.29042991 I purchased the timer and wanted to know how to replace it in the machine. I notice there is a cam and an arm on the front of the switch. After taking it apart do they need to be aligned in a particular way? Also does the front panel come off by just releasing the two screws on the top right an left? Thanks.
1 Answer Hi Squash. The cam lever aligns at 12:00. The timer cam installs in front of it going on one way only. The knob skirt notch and rear pin aligns at 12:00. Let us know if we can assist further. Thank you. Read More...
Squash September 03, 2011 for Model Number 417.29042991 Washer cycles but when it is on final spin it does not spin fast enough to wring water from clothes. Same thing on all final spin cycles. Someone suggested the timer, hard to see how but anything is possible. Had a technician out here and he cleaned drain. washer worked for awhile but has since exhibited the same problem.
1 Answer Squash, I would not suspect the timer, at this point. Just like before, you need to check the tub to pump hose and drain hose for clogs and the drain pump for clogs and the impeller vanes for damage 137108000. Thanks and Good Luck Read More...
Greg March 20, 2011 for Model Number fwt449gfs2 I tested the motor and other connections the paper work in the back of the washer said to test. All good. Washer will fill and drain, but will not spin.
Aaron March 17, 2011 for Model Number FWT645RHS1 My washer won't spin. There is a weird hissing noise coming from the timer area. Is this the motor or the timer?
1 Answer Hello Aaron! If the timer 131800500 is stuck on a cycle and will not advance over to spin, you will need to replace it. Thanks! Read More...
Lt March 11, 2011 for Model Number FWTT449GFS1 Washer will not advance to the next stage or next setting. When you manually advance it, it works. Is this the Timer or the switch?
1 Answer Hello LT. It sounds like you have a bad timer on this machine. Hope this helps. Read More...