Romeo July 28, 2015 My washer recently started to agitate and fill at the same time, hums when timer is in 'off' position and now it does not stop when timer switch is pressed in. Have to pull the plug to stop.
1 Answer Hello Romeo. You will need to order and replace the pressure switch on the unit. Read More...
Bob April 05, 2014 for Model Number WWS833ESO Washer will not agitate and timer will not move when in that cycle. If I move the timer to fill, it will fill and the timer will advance and spin out the water.
1 Answer Bob, The timer 131758600 is the components to start with. Sounds like there is a damaged internal cam or cam switch, that won't complete the circuit and allow the motor to run and the timer to advance in that increment. Read More...
John March 05, 2014 for Model Number FWX833AS1 Washer fills and start to agitate, but wont spin or drain
1 Answer Hello John. You need to check the lid lock assembly and see if it is bad and needs to be replaced on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Jeff November 19, 2013 for Model Number FEX831FS1 Washer takes a really long time to go through cycle.
1 Answer Hello Jeff. Test for power to the timer motor. If it is there, and the timer turns to slow, replace the timer on the unit. Read More...
Manuel October 08, 2013 Hi, I have a timer signed 131758600A. I should like if it is compatible with 131758600B. Thanks
1 Answer Manuel, Yes the 131758600b will work in place of the 131758600a. This is just a series change number. Read More...
Josse March 22, 2013 My washer fills and start cycle but when I turn it to spin cycle it will not spin out.
1 Answer Hello Josse. Check the lid switch on the unit and see if it is bad. If so, it will cause this issue. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Dannielle January 07, 2013 My washer fills but will not start cycle. When I turn it to rinse it puts water in but will not drain. When I turn it to spin cycle it will not spin out.
1 Answer Hello Dannielle. Based on the information you provided, you will need to check and see if the lid switch is bad and will need to be replaced on the unit. Read More...
Russ November 28, 2012 for Model Number FEX831CSO The washer will go thru the wash cycle, spin out, but when it refills for the rinse the water doesn't fill the tub, just keeps pumping out. It you pull the knob it will stop and if you turn it abit it will go into the spin cycle but you don't get the complete rinse cycle. Any suggestions?
1 Answer Hello Russ, You may want to check to see if the unit is siphoning when filling. This will happen if the drain tube is pushed too far down into the pipe or if the drain is too low. Also check your air hose that goes to the pressure switch to make sure that it is not clogged or pinched. Check for blockage of the drain pump that may be causing the unit to drain for too long of period. Read More...
Paul B November 25, 2012 for Model Number GLET1031FS0 Washer fills, washes normal. all cycles. will not pump out water.water can be emptied on spin cycle. sounds like grinding noise while spinning. does not seem to spin at full speed. when water is emptied, begins rinse cycle. End of rinse cycle, timer "ticks" constantly, water does not pump out, until spin begins. What do I need to replace.
1 Answer Paul, Your first check needs to be at the drain pump assembly 137221600 and hoses. The tub has to partially drain, before the tub will spin, and the noise and poor drain characteristics could be due to the drain pump or clog in the drain hoses. Read More...
Tracy October 23, 2012 for Model Number FEX831FS0 My washer fills up , but doesn't stop & agitate...it just continues filling to the point of overflowing..if I stop it and put it on the spin cycle, it does spin out...could I need a new timer?
1 Answer Hello Tracy. If you can stop the water from entering the machine by turning off the timer or unplugging the unit, you will need to look for a bad pressure hose or replace the pressure switch. If the only way to shut off the water is at the shut off for the water hoses, you will need to replace the water valve in the unit. Read More...