Greg October 19, 2023 for Model Number FGHS2631PF4A Having problems dispensing ice cubes and crushed ice .. The water dispenser work fine though. The auger and solenoid don't turn on when ice buttons are selected to dispense ice. Tried the diagnostic mode test #10 and #11 and the auger and solenoid come on as described, but back in normal ice mode the flapper doesn't activated the auger or solenoid. Some of the LED display segments are dim or out completely on the UI interface. Whats the next step? Replace UI board? Thanks
1 Answer Greg, This issue will be caused by a faulty User Interface Control board that will need to be replaced. Read More...
Ian September 26, 2023 for Model Number FGHC2331PF6 Problem is I push for ice on control board and powers off refrigerator entirely. Otherwise everything else seems to work, like water etc. What should I do?
1 Answer Ian, If the unit is shutting down when you put it on ice then this will be a faulty User interface that would need to be replaced. Read More...
Dave April 20, 2023 for Model Number FGSS2335TF1 Fridge LEDs stopped working. Freezer ones work fine. Tested all LEDs from fridge in freezer and all work fine. Tested door switch with multimeter and works fine. What else is there to test? Main board? How do I get at it? Thanks in advance
1 Answer Dave, the main control 5304507449 would be located just behind the kickplate and is accessed by pulling it forward. It can be tested for 12VDC using the wires at pin 5 and pin 6 of connector J4 when the refrigerator door is opened. If there is not voltage, the main control has failed. If there is voltage, there is a wire failure. Read More...
Jm February 03, 2023 for Model Number FGHC2331PFAA The fridge is too cold, won't let me raise either temp on the freezer or fridge. I can lower the temp on both and can only raise it to the temp I started at.
1 Answer Make sure the display is set for the scale you want F or C. Then unplug the fridge for 20 minutes to clear the memory on the control. Plug it in and if no change the control would need to be replaced. Read More...
Civilsalmon December 08, 2022 for Model Number FG4H2272UF I have a frigidair refrigerator from 2019. It's the frigidaire gallery. Some pop was spilled in the fridge and ate away at the wires for the lower freezer door ui. They then came our and shorted together. The user interface on the door died and has been since replaced. When that was replaced I also replaced the main control board as well. Now when the fridge is turned on the user interface doesn't want to boot and every light is on and won't turn off. The fridge still won't cool. Not trying to investigate on what to do next.
1 Answer Civilsalmon, Based on the information provided and if the wiring that was damaged is in the cabinet then it will not be repairable. If the wiring was in the door then the door would likely need to be replaced along with any of the components damaged by the shorted wiring. Read More...
Tasha August 29, 2022 for Model Number FG4H2272UF After a power outage and surge the fridge user interface is fully lit up ( every single light on) but is non responsive, the interior lights do not come on and the fridge condenser fan starts up but shuts off seconds later. it is not the main PCB board or the inverter as both have been replaced.
1 Answer Tasha, based on the information provided, it sounds like there is a shorted part. A shorted fan motor, interface 5304528575, or wire could potentially cause this issue. If each fan is accessed and unplugged one at a time, this could identify if it has failed as the unit will operate properly once a shorted part is unplugged. Read More...
Peter April 26, 2022 for Model Number Frigidaire FGUS2645LF1 My fridge and freezer work it makes ice but the interface does not work and the water/ice switch does not work. Also the inside lights dont work. I unplug it and when I plug it back in the display light comes on but goes out. Is it the interface or main controle board
1 Answer Peter, Test at the dispenser board for between 7 and 12 VDC and if there is proper power then replace the dispenser board. If not then replace the main board. Read More...
Janet October 08, 2021 for Model Number PLEB27S9FCB When setting the temperature it will only accept 2 numbers..for instance… I try setting the oven for 350….only 35 shows up. Do I need a bulb replacement or fuse or a new display panel? Thank you. J Fisk
1 Answer Hello Janet, the control board with display is part 316418721 however, it has been discontinued by the manufacturer and is no longer avaialble. Read More...
Daniel May 31, 2021 for Model Number FGHC2331PFAA Frigidaire Gallery side by side - FGHC2331PFAA -all interior lights in fridge (4) and freezer (1) (incandescent not led) not working. I replaced one blown bulb. No help. Everything else is working fine. help please
1 Answer Daniel, If none of the lights are working then this will most likely be an issue with the main control board part number 5304498781. Read More...
Keith August 26, 2020 for Model Number FGHC2331PFAA The display that shows Freezer and Refrigerator temp have segments of their LED lights missing/not displaying. Is that the whole user interface to be replaced or just bulbs or something. Not sure which part, looks like other questions on this board pointed to 2 different parts. thanks!
1 Answer Keith, the missing LED segments would be due to a failed user interface 5304527931. Read More...