Sharone Williams April 16, 2020 for Model Number HVM1540DN1BB Hello: I am trying to price a black touch pad for my microwave. The express buttons work, but all other buttons do not. It's the control panel that is faulty and needs replacing? Can you please provide me with a quote, If I am correct?
1 Answer Sharone, The part number for the touchpad will be WB56X10816 which is the control panel for the unit. Read More...
Mel December 07, 2018 for Model Number JVM1540DM1BB When I plug the unit in, the circuit board makes a buzzing sound and the interior and exterior lamps come on dimly but nothing else works.
1 Answer Hello Mel, You will need to change all three door switches to correct this issue. You will need two WB24X10047 and one WB24X25397. Read More...
Patricia March 06, 2017 for Model Number CONTROL PANEL WB07X10987 SORRY I SPEAK SPANISH, TENGO ESTE MICROONDAS QUE YA CASI TODAS LAS TECLAS DEL PANEL DE CONTROL ESTAN DANADAS, NECESITO ESTE REPUESTO , PODRIAN CONSEGUIRMELO? GE WB07/10987 AP3993698 GRACIAS PATRICIA
1 Answer Hola Patricia. Sí, basándose en la información que proporcionó, deberá solicitar y reemplazar el panel de control de la unidad. Gracias. Read More...
Jan July 24, 2016 for Model Number JVM1540DM5BB My Mcrowave will turn on but it will not heat anything by ordering the control panel will that help model#JVM1540DM5BB part#AP3993440
1 Answer Hello Jan. You most likely have a "high voltage" side malfunction. Transformer, diode, magnetron, Capacitor. You will need to be extremely careful if you decide to test the components with a multi meter, Very high residual voltage is present, so make sure you remove power to the microwave and short across the terminals on the capacitor. The magnetron should have a reading of less than 1 ohm resistance across the two terminals, and an "open" circuit between each terminal and chassis ground. The diode/rectifier should have a resistance reading in one direction only, no resistance, or resistance in both directions indicate a faulty diode. The primary winding on the trans former should read approximately 450 Ohms resistance, the secondary winding should read 80 ohms resistance, and the filament transformer should read 100 ohms resistance. If all the readings are proper and in range, replace the magnetron. Read More...
Sam G. February 27, 2016 for Model Number EWAVE MICROWAVE Fuse blew. When I replaced it, with the door closed everything seemed to work. When I opened the door, the fuse blew again. PLEASE HELP
1 Answer Sam, You will need to check or replace the door switches and or adjust the door switch bracket. One of the switches(usually the monitor switch) Is wired to be a direct short to ground, if the switch is faulty or not activated properly, the fuse will blow, to keep the machine operating in a safe mode/fashion. Read More...
Joseph September 04, 2013 My control panel shows a panel short repair may be needed on my GE JVM1540DN1BB. I see a control panel ap4360661 for $139.00 and control panel ap399344d for $61.00. What is the correct one to order or perhaps a different one? Thank you
1 Answer Hello Joseph, Since your unit is black, you will need to order part number WB56X10822. Read More...
Robin September 24, 2012 for Model Number JVM1540DM5BB We have scratched the surface on the control panel of our new microwave, everything still works, do we need to order the entire control panel, or can you just replace the face for cosmetic reasons?
1 Answer Robin, you will have to replace the control panel WB07X11008 as the manufacturer does not offer the touch panel separately. Thanks! Read More...
Bruce August 02, 2012 for Model Number JVM1540DN1BB On the touch pad the vent fan, number 2, and number 8 buttons no longer functioning. All others are fine. What are the chances of corrosion over bad touch pad assembly? Reason I ask is because the unit is in my rental property so don't want to distrub tenants twice, once to check connection and if bad another to replace touch pad, but if chances are good it is only corrosion I will give it a shot to clean before buying a replacement touch pad. If it is corrosion then how does one clean the corrosion?
1 Answer Hello Bruce. Most likely, the control panel WB07X11008 is bad and will need to be replaced on the unit. You can try cleaning the ribbon cable, but usually it needs to be replaced. Read More...
Bob M. November 27, 2011 for Model Number HVM1540 Only the express buttons (1-6) work, no clock, start clear etc. is the touch pad bad or the smart board?
1 Answer Hello Bob. Based on the information, it sounds like the control panel WB07X11008 is bad and will need to be replaced. Hope this helps. Read More...
Pjr October 19, 2011 for Model Number JVM1540DM1BB When I plug my control panel in, it tells me there is a short, service may be needed. Do I need to change the control panel, the touch pad or the smartboard?
1 Answer Hello PJR. Based on the code you are getting, it sounds like the control panel WB07X11008 is bad and will need to be replaced. Hope this helps. Read More...