Customer Questions and Answers for Range Lp Conversion Kit by Ge

Hello Paul. Sorry, there is no kit to go back to natural gas. Also, the right front burner WB28X22841 has been permanently discontinued by the manufacturer and we don't know of any source or replacement for the part. You still can order the other 4. They are WB28T10252, WB28T10260, WB28T10253, and WB28X29275.

Scott, The LP Gas Conversion kit for the model number you supplied is WB28X39132 / WB28X24757 . The part is in stock and available at this time. The part is $18.43, shipping is $8.95 and any applicable tax (CA. PA. TN.) . Thanks,

Dan, Yes the WB28K10556 / WB28K10556 Conversion Kit is the correct part to order for the model number you supplied. It also has instructions for the proper conversion to LP gas, so You'll have everything you need. The part is in stock and available at this time. Thanks,

Hello D.T., You will need the following orifices: WB28T10151 for the Left Rear, WB28T10033 for the Right Front, WB28K10288 for the Right Rear, WB28T10017 for the Left Front, and WB28K10288 for the Center. This is presuming the complete model number is ZGU36KBK1BB, (There are 7 different variations of the model number provided).

Hello Genti, You will need to order the following parts for the surface: WB28K10187, WB28K10188, WB28K10189, and WB28K10190. The oven is adjustable by turning the orifice hoods clockwise 1 1/2 to 2 turns or until bottomed, (without overtightening), and convert the Regulator. To convert the regulator, remove the Large hex-nut which is located in the center of the regulator. Remove the plastic pin from the bottom side of the cap, turn the pin 180 degrees and snap the pin back into the cap. There are raised letters on the flat side of the plastic pin, “NAT”. and “LP”. In the “LP” position the end of the pin marked “NAT” should be snapped into the bottom of the hex-nut.

JD, To convert the regulator you would remove the cap on the regulator and flip it from LP to NAT. For the oven you would loosen the orifices about 1 1/2 to 2 turns and adjust the air shutters on the end of the burners.

Hello Shanda, As per the tech sheet: Convert the appliance pressure regulator. a. Use an adjustable wrench to unscrew the hex-nut cap from the pressure regulator. b. Apply pressure and turn counter clockwise to disassembly the plastic cap. c. Turn the cap over and hook it into the slots. The type of gas to be used should now be visible in the top of the cap. d. Screw back the hex-nut cap into the pressure regulator. Install the LP Orifice Spuds for the Top Burners: Four spuds are supplied with the range and are mounted in a bracket next to the regulator, (If they were returned to the proper position by the previous installer). Convert the Oven Burner Orifice to natural gas: Using a 1/2 open end wrench, turn the orifice clockwise until the orifice tightens "snug". Do not overtighten as damage to the orifice pin, below the orifice hood may result. (Note the natural gas orifices are brass and the LP orifices are silver). Light the Oven Burner and Adjust the Air Shutter as Needed. Adjust the Low Flame Setting on models with 270 degree rotation valves. If the original orifices cannot be located, I'm sorry but you will have to contact the manufacturer for the orifice sizes since they are not provided on any literature published on this model.

Cathi, To convert this unit from LP to natural you will need 2 medium orifices WB28K10022 for the left front and left rear, one small WB28K10029 for the right rear, and one large WB28K10030 for the right front. For the bake you would loosen the orifice 1 1/2 to 2 turns and adjust the air shutter on the burner.

Emily, The WB28K10556/WB28K10556 Conversion Kit is a Nat gas To Lp gas Conversion Kit. To Go From Lp Back To Nat Use 1) Wb28k10187 1) Wb28k10188 1) Wb28k10189 And 1) Wb28k10190 the oven orifice hood should be adjustable.

Hello Marcia, You will need the following: ORIFICE SPUD RF 170 NG WB28T10206, ORIFICE SPUD 145 NG WB28T10197, ORIFICE SPUD 95 NG WB28T10195, and ORIFICE SPUD 130 NG WB28T10196.