Annie September 04, 2014 for Model Number DPSR473GWOWW My GE dryer is making a loud sqeeking noise like metal rubbing against metal and my cloths keep getting caught in drum front support bering. If I replace this piece do you think this will solve the noise and cloths catching problem?
1 Answer Hello Annie. You need to order WE3M26, WE03X37318 X4, and WE25M40 to repair the unit. Read More...
Ray April 09, 2014 for Model Number Dccb330ejwc Our dryer makes a racket (sometimes) . We replaced the slides but still make a racket. If it was a car you would thing it was throwing a rod. What is it?
1 Answer Hello Ray. Check the belt, and the rear bearing on the unit. See if either is causing the noise. Also, check the idler pulley. Read More...
Tc April 08, 2014 for Model Number DBXR463ED1WW Hello! I replaced the WE3M26 and bearing slides, but after a few minutes the dryer will just shut down unexpectedly, and then start up again. This is on timed dry as well as auto dry.
1 Answer Hello TC. If the unit is over heating, you will need to order and replace the motor on the unit. Read More...
Dennis March 11, 2014 for Model Number DWSR473EV0WW Tool Time Dennis here, this will be a big step for me...REPAIRS!!! YIKES !!! $90 to drive to my house to repair my dryer, no thanks, so here goes. I watched the video and looks easy enough but theres always a but...where do I find the "SLIDERS
Shannon March 07, 2014 for Model Number DPSE810EG0WT First off a big thank you. Your videos are a tremendous help. They gave me the confidence to tackle this project. I had a bad squeaking issue with the GE Profile Dryer (DPSE810EG0WT) and a lot of black dust. I purchased and replaced drum support bearing, all 4 drum slide/glides, drive belt, felt seal, idler pulley and drum bearing kit. Put it all back. No more squeaking! For a lack of a better term it is making a faint almost "swooshing" sound. It didn't make this noise when rotating the drum manually when I was aligning the belt. Happened after attaching the front panel support. Any ideas of maybe something I did incorrectly. Could it be the drum against the new felt seal? Or is it normal with the new drum glides? Again, thanks for the parts and great videos!
1 Answer Shannon, When replacing the bearing glides it is normal for the unit to have the swooshing type noise for a little while and then it will go away. Read More...
Jason R. February 14, 2014 for Model Number DBXR453EVOWW I have excessivly load squeaking when dryer is running alot worse with a heavier load. There is play in the drum front to back. Could you please tell me a list of parts that I would need to repair my dryer? Thanks for all your time and help!
1 Answer Hello Jason, You will need to order a rear drum bearing kit WE25M40, the dryer drum front support bearing WE3M26, two white bearing slides for the outside WE03X37318, two green bearing slides for the insides WE03X37317, and an idler pulley WE12X83. Read More...
Lori January 11, 2014 for Model Number DBXR463EDC1CC front load electric GE dryer Dryer squeaks loudly, when drying especially on a heavier load. I noticed the noise loudest near the top of the door. I also noted a lot of play front to back on the front drum support. I placed a small amount of vegetable oil into the front drum support, the squeak stopped, however I realized this is only short term. I need to replace the slides and the front drum support, can you tell me the exact part numbers for this electric dryer. DBXR463EDC1CC
1 Answer Hello Lori, The rear drum bearing kit part number is WE25M40. The inner white slides, (two of these), are WE03X37318. The two outer slides, green, (two of these), are WE03X37317. If the front drum bearing WE3M26, (the part the slides fit into), has been worn down, it will require replacement also to prevent premature failure of the other parts you are now replacing. While inside the unit, remove the idler pulley and clean the pulley arm where the pulley rides with a dry paper towel and if sticky, use a dab of rubbing alcohol to cut the residue from the softener sheets. Read More...
Scott November 13, 2013 for Model Number GE Elec. Dryer DWSR483EA1WW I am replacing part # WE3M20 with AP3790641. I have only one green bearing slide left on the old unit. I know I need four on the old part...What slide do I need for the replacement front support bearing? the ones I see are showing as "white in the parts list. My slide bearings are like rubber and have notched holes to hold them in place.
Judy November 09, 2013 for Model Number DVLR223EE2WW I replaced the drum front support bearing. Now the drum is not turning when I turn it on.
1 Answer Hello Judy, Does the dryer motor come on or is the machine silent? You may have inadvertantly unplugged one of the wires to the door switch when you removed the front panel. Read More...
Patrick November 04, 2013 for Model Number GE DWXR473ET1WW Hi, I am looking to order the dryer drum front support bearing and the bearing slides for my dryer. What slides would I need for dryer model DWXR473ET1WW?
1 Answer Hello Patrick, The front support bearing is WE3M26 and you will need two white slides WE03X37318 and two green slides WE03X37317. The green ones go in the center. Read More...