Paul October 18, 2014 for Model Number WR30X0327 I need the cam for this ice maker. It's part number is AP2068422. It shows is as not available. Is there a replacement part?
1 Answer Paul, parts to the icemaker are no longer available separate from the icemaker assembly, part number WR30X10093. Thanks. Read More...
Olayinka Onadeko October 09, 2014 for Model Number ESS25LGPACC Thank you for responding to my previous question. Now the water is dispensing. The tubing in the back of the unit was blocked. The problem now is the ice dispenser. It seems the ice dispenser works but the ice will not completely come out through the chute. About 2 cubes of ice may dispense, but the rest blocks the flap from closing up. As a result, the ice freezes over again allowing air to enter and ice frost forms in the dispenser. Please advise on a corrective action. Thanks
1 Answer Olayinka, First check the size of the ice cubes, the cubes should measure less than one(1) inch in the center of the crescent(usually 3/4 to 7/8 inch is average). Remove the ice bin and check the front housing trap door. make sure it opens completely. Oversized cubes or a sticky trap door could create the issues you described. Make sure the end of the bin shifter arm is installed in the solenoid yoke properly. Read More...
Cthomp October 08, 2014 I installed the GE WR30X10093 ice maker on a new Hotpoint Model HPE15BTHBRWW fridge. I used a generic water valve I bought at Lowe's and it's not working right. What water valve is compatible with this maker & fridge? I have a GE WR57X10051water valve which is a dual valve. Will this work if I hook the side for the ice maker?
1 Answer Hello! For new icemaker installations you would have needed to install the correct icemaker add on kit. If you installed part number IM6D or the original IM6 icemaker install kit. The valve is part number WR57X10033. Thanks! Read More...
Dave October 07, 2014 for Model Number GSRL3KLXAFLB Hello we have a side by side GE fridge with ice maker.it just stopped making ice .I notice that the on/off switch slides back and forth but the paddle stays in the off position.so the paddle does not move.I put the switch to on position and nothing happens Still no ice and help thanks Dave
1 Answer Hello Dave. Based on the information you provided, you will need to replace the icemaker in the unit. Read More...
Olayinka O October 04, 2014 for Model Number ESS25LGPACC I have a side by side refrigerator. The ice maker is making ice in the bucket but when you press the button for ice or water, there is nothing dispensing out when you press down on the flap. We manually have to pick out the ice from the bucket. At one time it was just the ice malfunctioning, but now, we can't get both ice and water. Please advise. Thanks
1 Answer Olayinka, With both the ice and water not working for your unit, the most likely cause for failure would be a bad dispenser board or a bad main control board. You can test to see if there is return voltage back to the main control from the dispenser when pushing the lever. It would most likely be the dispenser board that is the issue. Read More...
Bill September 26, 2014 for Model Number GSS25JFPBBB Can you remove the same ice maker from a side mount freezer compartment and adapt it to a rear mount freezer compartment? from the parts diagram, GE #AP2345120 looks to be the same replacement for both freezer ice makers.
1 Answer Bill, Yes the icemaker kit WR30X10093 can be mounted on the side or in the rear of the unit. Read More...
1 Answer Hello John. Test for power to the water valve. If there is power there, and no water out of the valve, replace the valve. If there is water coming out of the bottom of the freezer door, but not the dispenser, then the water line in the door is frozen and will need to be thawed out. If so, you will need to install the dispenser water tube heater WR49X10173 for the unit. Read More...
Craig September 18, 2014 for Model Number Mod: TFX28PBDAWW Ser: MZ278483 I have a GE S/S refrigerator freezer, 24CF & OVR. It is not letting water into the ice maker but the water dispenser in the door works fine. The water line for the door came off and I reconnected it and it is working good. I checked you tube and most of the info says the ice maker motor has stopped working. Before I order this I'd like to make sure it isn't a solenoid in the back that allows the water to flow into the ice maker or is it the ice maker motor? Model No. TFX28PBDA WW, serial no. MZ278483.
1 Answer Hello Craig. Make sure the freezer is between 0° and 5°. You need to check and see if there is power going to the water valve when the icemaker cycles. If so, replace the water valve on the unit. If not, or the icemaker does not cycle, you will need to replace the icemaker on the unit. Also, check and make sure the fill tube on the unit is not frozen and clogged. If so, replace the water valve and thaw out the fill tube. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Josh September 15, 2014 for Model Number Old GE Fridge Hey there! My fridge has a sticker on the back that says: "This refrigerator will accept accessory icemaker UK-KIT-4 or IM-1." Will this kit work with it?
Rick K September 07, 2014 for Model Number TPX21PRXAWW I got the ice maker but it is for a side feed water tube mine is in the rear of the freezer,I can't change out the fill cup to the old one because the tabs don't line up.
1 Answer Hello Rick. The fill cup supplied with the new icemaker can either be installed on the end or the middle of the icemaker. Read More...