Dan December 20, 2012 for Model Number GE PFSS2MJYCSS Ice maker fails to make ice. Checked line to maker from solenoid by blowing and is clear. Applied 120v to solenoid and seems to come out ok (energizes). Can get 120v to connector by switching ice maker on/off but when connected to solenoid does not seem to energize. There is a horizontal lever on the ice maker that moves horizontally back and forth, does this also raise up and down to tell when ice is full. Maybe it is stuck in the up position? Not sure why green light flashes, maybe detects some type of error or malfunction? when I switch off then on it stays lit. I do hear a noise like something is turning. I am concerned to just replace the solenoid if there is a circuit board somewhere that may be the problem.
1 Answer Hello Dan, The light flashing on the icemaker is an error caused by the icemaker. The icemaker WR30X10093 will need to be changed. Read More...
Luke December 14, 2012 for Model Number PSF26PTA WW Ice is wet and sticking together. I emptied ice maker and it is making ice at a very slow rate and water is running out of ice bucket. What would cause this?
1 Answer Hello Luke. You need to check and see if the icemaker is leaking water. If so, you will need to order and replace the icemaker WR30X10093. If not, and the icemaker is over flowing, you will need to replace the water valve WR57X33326 on the unit. Read More...
Barbara December 02, 2012 for Model Number PSF26pgwabb Ice maker. Ice cubes become wet and then freezes up. If I have ice cream on that top shelf under ice cube bucket it will sometimes become soft. What is the problem? Thank you
1 Answer Hello Barbara, This is either the defrost thermostat WR50X10068 never opening of a set of contacts in the ice maker WR30X10093 that is keeping the mold heater on too long. Read More...
Edwin S November 28, 2012 for Model Number Side by side Mod. TFX24RLL I have do not energy in the water supply valve to ice maker ( electrical cable without energy). The dispenser water's valve is Ok and it is working normaly.
1 Answer Hello Edwin, When you check the valve you should receive 120vac when the icemaker gets to the part of the cycle to call for water. If at this point you are not getting power then the icemaker is not sending signal or you are loosing power between icemaker WR30X10093 and water valve. Read More...
Bill November 26, 2012 for Model Number PSS26SGPASS My icemaker doesnt work..I replaced the water inlet valve, now the water dispenser works..when I reach in and turn on the icemaker it starts to fill and turns off..i defrosted the unit.. the green light is on..it was blinking previously..any help is appreciated. Thank you
1 Answer Hello Bill. The blinking green light is a fualt code and the icemaker WR30X10093 will need to be replaced in the unit. Read More...
Kirk T November 23, 2012 for Model Number PSC23SGNA BS How do you remove the ice maker unit to replace it.
1 Answer Hello Kirk, To remove the icemaker kit you would first remove the ice bin and upper storage tray. There is a screw on the left side of the icemaker that holds it in place. Remove screw and icemaker will slide forward. There are clips on either side of the wiring harness that you lift on one side and then the other to remove. Read More...
Rosemary M November 20, 2012 for Model Number TFX25JPCGWW My icecube maker will work for a few days then it quits, then after a week or two it will start again. What is the problem?
1 Answer Hello Rosemary. Check and make sure the temperature is around 0° inside the freezer. If so, you will need to order and replace the icemaker kit WR30X10093 in the unit. Read More...
Randyj November 06, 2012 for Model Number hss251fmdww Hotpoint HSS251FMDww. I put the icemaker in test mode (off for 30 seconds, pushed arm 3 times). It cycles and harvests. However, it still is not harvesting when left to do its own thing. Am I doing something wrong? I just replaced the main control board today. The icemaker hasn't been working for over a year and we have had electrical problems with our power meter (got that fixed, new meter). I also replaced the defrost fan motor.
1 Answer Hello Randyj. Based on the information you provided, it sounds like the icemaker kit WR30X10093 is bad and will need to be replaced on the unit. Read More...
Mark D Thomas November 03, 2012 for Model Number gss25qgta bb Hi my question is about the GE model gss25qgtabb. What I'm looking for is the white piece that prevents the ice from re-entering the tray. It's the part that lets the ice pusher's fingers go threw. I will take a used one if you have it. Thanks, Mark
1 Answer Hello Mark, if you are looking for parts on the ice maker, I'm sorry, GE does not provide any parts for this ice maker. They only sell the ice maker as an assembly. Thanks! Read More...
Raymond October 29, 2012 for Model Number wr30x10093 I recently purchased an ice maker for my frezer. The original one was removed by a ge technician and i disposed of it after ordering the new model. After the new part arrived I began install and realised my freezer did not have the mounting bracket in place. I am unsure how the original was installed as i did not see its removal by the technician. Is it possibe there is another installation method or could I have disposed of the part with the original ice maker. Would it have been attached tot he ice maker?? I would think not and if so is there another part , bracket or otherwise that i can purchase to install properly? Confused!
1 Answer Hello Raymond. We will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...