Customer Questions and Answers for Refrigerator Ice Maker Assembly by Ge

Hello John! The manufacturer does not offer parts separate from the icemaker assembly, the icemaker assembly will need to be purchased WR30X10093. Sorry about that!

Hello Donna. You need to check and see if there is power going to the water valve when the icemaker cycles. If so, replace the water valve on the unit. If not, or the icemaker does not cycle, you will need to replace the icemaker on the unit. Also, check and make sure the fill tube on the unit is not frozen and clogged. If so, replace the water valve and thaw out the fill tube. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Hello Big Ron. This is the only icemaker kit GE offers at this time. In order to install the bucket, you will lift the front of the bucket and slide in the back of the bucket and make sure the wire for the icemaker is out of the way when sliding it back into the unit.

Ed, It sounds like your water fill switch has failed, and or the water adjustment screw, spring, linkage and cam wheel, may have become dislodged and is causimg the water valve to remain active at all times. You could remove the ice maker front cover and check the switches and cam linkage etc. But your best and safest bet would be to replace the assembly WR30X10093.

Hello Fred. You need to check and see if there is power going to the water valve when the icemaker cycles. If so, replace the water valve on the unit. If not, or the icemaker does not cycle, you will need to replace the icemaker on the unit. Also, check and make sure the fill tube on the unit is not frozen and clogged. If so, replace the water valve and thaw out the fill tube. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Hello Denise. No, there is no filter. You may need to replace the water valve WR57X10033 and line WR17X1948 on the unit to remove the tase from the ice.

Hello Sonny. You will need to order and replace the water valve WR57X33326 on the unit. Make sure you thaw the tube out as well on the unit.

Hello Sonny, The forced cycle is done on a timed basis, so you have to be prepared before getting started. First, unplug the unit for a minimum of 2 minutes. During this time, tape down the freezer door switch. Once this is accomplished, plug the unit back in and within the first 30 seconds after power up, actuate the ice flapper three deliberate times. This should force the ice maker to cycle. If it doesn't cycle and you're sure you went through procedure properly, the ice maker could have an internal issue. If it didn't cycle, you may want to try it several times to make sure since the units are sensitive to the time limitations.

Chris, It won't be difficult at all, If you have "basic" tools and skills. Just remember to remove power to the refrigerator and read the instructions that are supplied with the new icemaker assembly. Now the water tube in the door freezing, check and make sure the freezer door gasket is sealing to the refrigerator cabinet front flange, check for moisture or ice on the inner and outer door liners. and make sure the dispenser flapper is sealing when closed. Check the freezer compartment air temperature( reccomendation would be 3 to 5 dgrs.) and definitely not below 0. Any moisture or ice on the door or liner would indicate an air leak around the door gasket, or a void in the insulation and the door assembly would need to be repalced.

Hello Still. You need to check and see if the auger is broke, or if the motor is not running, you may have a bad auger motor WR60X10262 and the motor will need to be replaced in the unit.