Sue October 07, 2017 for Model Number GTWN5050M0WS Is WH12X10475 or WH12x10508 the correct part# for the control board on GE washer GTWN5050MOWS? When my nephew looked up the part # for this model, it came up WH12X10475. When he removed the old control board, the part # was WH12X10508. WH12X10475 did not fix the machine which will not fill, so I was wondering if this was the correct part.
1 Answer Sue, The part number for the control board on this unit will be part number WH12X10475. Read More...
Sue October 07, 2017 for Model Number GTWN5050M0WS Washer would not fill, fill light flashed and beeped. Troubleshooting indicated a faulty control board. Replaced board but still no voltage from control board to fill valve. Old control board appears to have been shorted. No error codes on motor. What should I do now?
1 Answer Sue, With this issue of there being no power to the fill valve then this will likely be a faulty pressure switch with the control board having already been replaced. Read More...
Peter July 28, 2017 for Model Number GTWN4250M1WS Washer fills, agitates, and drains. It continues to drain but does not enter spin cycle. Lid switch checks ok. Motor light flashes continously. What do I check next?
1 Answer Hello Peter. You will need to look for a clogged pressure hose and check for a bad pressure switch. Until this unit is empty, it will continue to drain. If it does not sense a drain is complete, it will not spin. When you access the inside of the control panel, the pink wire from the pressure switch to the control board should read open for continuity when the washer is empty of water. If not, then the hose is clogged or the switch is bad. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Fred R July 16, 2017 for Model Number GE GTWN4250M Does not fill with hot water when HOT/COLD selected, does cycle between hot and cold water when WARM/COLD is selected.
1 Answer Fred, This issue would most likely be caused by a faulty control board WH12X10475. Read More...
Dale April 10, 2017 Replaced lid switch on GTWN4250M0WS. Washer fills with water but does not advance to wash cycle. While filling it continues to beep as if lid is open. No error codes on motor. Is this a faulty control board not allowing it to advance and assuming the lid is open?
1 Answer Dale, You will want to check the magnet on the lid of the washer to make sure that it is not damaged or deteriorating. If this checks ok then the issue will most likely be caused by a faulty control board. Read More...
Robert March 11, 2017 for Model Number GTWN4950L0WS Original question......So my washer is just stuck in drain cycle, put clothes in and press start....the water comes in and drum spins and water is just being pumped out....put in service field test and no codes show up to clear...I replaced the pump thinking it was pump but still issue of water spinning out...no matter what setting I put it on it's the same issue.....looked at motor flash code, that too is normal flash.........before I replace control board, does anyone know what else I could check.....Thanks." Ordered control board and replace......machine still does same thing....so at this point I'm about $150 in repairs by replacing pump and control board, what else can it be...pressure switch ?
1 Answer Robert, Check to make sure that the pressure hose is not clogged. If it is not clogged then would be an issue with the control board WH12X10475. Read More...
Stevent1976 March 08, 2017 for Model Number GTWN4950L0WS So the washer won't turn on. When you select the cycle and press the start button it beeps three times and the full light flashes continuously. After about 30 seconds it beeps twice and continues flashing. It does this repeatedly until I press and hold the start button to cancel the cycle. I replaced the magnetic lid switch already. Any ideas what else I should look at?
1 Answer StevenT1976, The most likely cause for this would be a faulty main board but you will want to pull the front panel off the unit and see if the motor board is flashing an error code. If not then the main board would be the issue. Read More...
Robert March 02, 2017 for Model Number GTWN4950L0WS So my washer is just stuck in drain cycle, put clothes in and press start....the water comes in and drum spins and water is just being pumped out....put in service field test and no codes show up to clear...I replaced the pump thinking it was pump but still issue of water spinning out...no matter what setting I put it on it's the same issue.....looked at motor flash code, that too is normal flash.........before I replace control board, does anyone know what else I could check.....Thanks.
1 Answer Robert, With the water coming in and pumping out at the same time then this would be a issue with main control board which would be part number WH12X10475. Read More...
Tmacsparky December 31, 2016 for Model Number GE GTWN4250D 1WS I do not have any cycle lights on my washer. I have already replaced the control board. Is there anything else I can check or is the board I just got bad? Thanks.
1 Answer Tmac, You will want to check the power supply coming into the control board from The long 10 pin connector pins 5 to pin 6 for 120 vac. If there is not 120 vac then go back to the power supply and make sure that there is 120 vac at the power supply where it comes into the washer. Read More...
Doug September 03, 2016 for Model Number GTWN4450M1WS this washer fills then just sits there and beeps. checked the fault led at the motor and is blinking 10 times. changed the control board wh12x10524 and have same issue. does this board need programmed? is the motor bad if this board is good? I have 120 volts to motor and some dc voltage to the motor although not what the spec sheets says. but the motor still isn't moving. so if I have these voltages does this mean the control board is working? also verified the door switch, .
1 Answer Doug, Yes if the main control board behind the backsplash did not correct the issue with the unit then the motor would be the issue and would need to be replaced. The part number for the motor will be WH20X10066. Read More...