Akk August 18, 2023 for Model Number GTWN4950L0WS Hello My GE washing machine GTWN4950L0WS does not fill water. When I put it in any mode extra heavy, heavy, medium, light, quick rinse, drain and spin or any other mode I only hear the water drain pump coming on and nothing else happens. When I ran the machine in field servie mode I got an error of "slow pump". I have replaced the triple water valve, pressure switch but nothing worked. I tried to reset the motor by opening the lid quickly 6 times. The machine runs in field service mode everything works as it should be. Can you please help with what is going wrong with my washing machine.
1 Answer Hello Akk, the control board may think the tub still has water in it and it cannot run a new wash cycle till the water is drained out, if there is no standing water in the tub, check for a restriction in the tub's air trap, kinked airline tubing or pressure switch problem. Read More...
C T December 17, 2022 for Model Number GTW485ASJ1WS Late one evening, I heard a noise from the laundry room. It sounded as if the pump was running, but the washer was not being used. None of the lights on the panel were lit up. I was not able to get it to stop without unplugging it. What could be the issue?
1 Answer CT, This would most likely be a relay on the main control board that is faulty and causing the pump to run continuously. You will want to make sure that water is not leaking into the unit when off because this could cause it as well but if not then change the main control board. Read More...
Junior March 24, 2022 for Model Number WPRE6150K Washer comes on but will not fill properly or agitate the way it should. It spins slowly and water steadily comes out. Spins as slow as my 100 year old grandma standing in one spot spinning in a circle. Lol if that helps. It does spin and drain after manually switching the modes. I thought it would be the circuit board at first, but don't wanna spend the funds on one and it be a waste of my money and time. Can you please steer me in the direction that would be suitable for the problems I'm having with this particular machine? Thanks and God bless
1 Answer Junior, Remove the front panel of the unit and check the light on the motor to see what sequence it is flashing in. The sequence it flashes in will determine if and what the problem is and the chart for flashes will be on the tech sheet inside your units control panel. Read More...
Jason October 27, 2020 for Model Number GTWN5050M0WS When I press start it just beeps two times and the Fill light blinks, but nothing happens. I've checked the Lid Switch with a Continuity Tester and the tester lights up showing the switch is good. I'm a novice so I assume I'm testing it correctly. The only error code I've seen is the 10 flashes, but even after replacing the control board the same thing happens when I press start. I've even done the Field Test mode and still do not receive any error codes. Could it still be the lid switch even though I tested it or something else? Thanks
1 Answer Jason, it would be recommended that the wires going from the main control to the motor are inspected for any pinched or broken sections as this can cause a miscommunication between the two parts. As the main control has been replaced, if the wires are good then the likely failure would be in the motor assembly WH20X10066. Read More...
M. July 02, 2020 for Model Number GTWN4250D1WS Washer fills, agitates, but won't drain and spin. It was doing this intermittently so I replaced the lid switch assembly. It worked fine for about 2 weeks and now it is once again filling, agitating but when it gets to drain and spin it stops filled with water. If we reset (unplug for a minute, open and close lid 6 times) and then manually switch to "drain and spin" it will complete the cycle some of the time. Other times we unplug overnight, plug back in in the morning, and manually do drain and spin and it works. Plug sparks when we plug back in. My best guess is the control board. Does this sound right? Thanks!
1 Answer Hello M., This could be caused by a bad control board but I would first try reprogramming the control. If this corrects the issue but the problem returns again, the issue is in the control not holding its' program. If not, there could be an issue with the pressure switch or a harness issue. Read More...
Charles August 21, 2019 for Model Number GTWN4950L0WS Machine runs on heavy cycle and sometimes on medium cycle. when it doesn't run it just stops in mid process, or doesn't start. I suspect it is the motor control board. Does the control board include the sandwich pc board.
1 Answer Charles, yes the WH12X10475 Motor Control Board does include the "sandwich" pc board. " the assembly is sold as a "complete" or single unit. The part is in stock and available at this time. Thanks, Read More...
Robbie June 29, 2019 for Model Number GTWN42501WS My machine doesn't fill as it should! I had this same problem while the machine was still under warranty! I think that the repair guy replaced the control board and the water level probe. Should I do the same and if so what is the board part number? Thanks.
1 Answer Robbie,In most cases, it is the pressure switch causing this issue.WH12X10412 Don't forget to check the hose also, If it appears damaged kinked or torn it will need to be replaced also.WH41X365 is the hose. Read More...
Janet J. June 07, 2019 for Model Number GTW680BSJ3WS We came home one evening to our washing machine having turned itself on. When I checked it it seemed stuck in a cycle with no water, but sounded like it was trying to drain. I have been trying to reboot it as advised by GE service department but this did not work. It was suggested that we need a new control board but saw 2 different ones on here and not really sure which one I needed. Also curious if this is difficult to replace and if you have any videos on here or could direct me to something I could watch before I attempt the repair?
1 Answer Hello Janet, The control board for your unit is WH22X35757. It does sound like this would be the issue. Read More...
Mark August 12, 2018 for Model Number GE GTWN4250D0WS Initial problem with washer started with no hot water when selecting warm or hot cycle. Check water valve and had power determined it may be a manual issue, valve replaced. Problem not solved. New issue followed with no water when starting washer, went straight to agitating. Check pressure switch and hose, hose was clear switch had continuity. Replaced pressure switch anyway, still not water (hot or cold) to washer.
Rachel July 16, 2018 I have a GE top loading washing machine and it won’t start. It’s flashing LID across its screen. When I checked for an error code it was 10 flashes, which according to the manual means a communication error and says to check the backsplash control. What do I do?
1 Answer Rachel, Check for any loose or damaged wires between the control board and motor and if this checks ok then the issue will most likely be an issue with the backsplash control board. Read More...