Daniel July 08, 2015 How do I test and replace if needed the water temperature probe sensor WH12X10410 on my GE washer?
1 Answer Hello Daniel, 'm sorry but you will need to please re-post with the model number so we can pull the wiring diagram on your unit. Thank you for your patience and understanding in this matter. Read More...
David July 08, 2015 for Model Number GHWN4250D0WW With the lid closed, only cold water enters the washer no matter what the water temperature setting is. With the lid open the correct water temperature enters the washer. If set on cold, cold water enters, warm then warm water enters, hot then hot enters. The water supply hoses are connected correctly and water fills to correct level.
1 Answer Hello David. See if the sensor is good and if so, you will need to order and replace the control board WH12X10614C on the unit. Read More...
Frank February 18, 2015 for Model Number WHRE5260E1WW I ordered probe sensor part number WH12X10251. How do I replace it? I can feel two screws holding the water inlet in place from inside the washer tub. Do I unscrew the water inlet and remove the old sensor. Does the new sensor just snap in the hole in the water inlet or does it screw in? Thanks
1 Answer Frank, "1. Remove the control panel. 2. Disconnect the thermistor wire harness from the water level switch. 3. Remove the funnel hose from the water valve. 4. From inside the tub, remove the two 1/4-in. hex-head screws that attach the fill funnel to the washer. 5. Pull the fill funnel and wires down through the opening. 6. Remove the tape, pull and unsnap the thermistor from the top of the fill funnel. ** Note: Make certain the gray rubber gasket is in place on the thermistor when reassembling." Read More...
Frank February 16, 2015 for Model Number whre5260e1ww This washer has PerfectTemp feature which senses the temperature of the incoming water and adjusts the fill water temp if necessary. For example, on cold setting, some warm water would be added, especially in the winter when the water coming into the house is really cold. On hot setting, some cold water would be added. This feature does not work anymore. Is it possible I need to replace the probe sensor Atc? Thanks
1 Answer Frank, the WH12X10251 Atc Sensor Probe is a possibility, but not the more likely issue. you can test the resistance of the sensor with a multi meter. it should have a resistance of 50K ohms resistance at room temperature. The more likely issue(s) would involve the WH13X10024 fill valve and/or the fill hoses. Remove the hoses and flush the faucets, check the debris screens in the end of the hoses, and the inlet to the fill valve, clean out any sediment or debris on the screens. It could also be that the control board is reverting back to the factory settings. The ATC / perfect temp circuit is allowed to cycle so many times(25) during a fill cycle before the control board reverts to the factory settings. with the resent weather conditions, the board could be resetting. Read More...
Chuck January 20, 2015 for Model Number GE Washing Machine GCWN5050M0WS When temperature is to Warm, I get hot water. The other settings seem to work correctly. Hot gives hot water, Cold gives cold water. How do I fix this?
1 Answer Hello Chuck, The water valves should cycle back and forth. The thermistor averages the temperatures dispensed and if the water for warm wash is hot you will need to check the resistance of the thermistor for about 47K ohms at about 77°F. If this WH12X10410 is more than 10% out of tolerance or out of its' correct installed position, it will need to be installed correctly or replaced. Read More...
Janet November 30, 2014 for Model Number wjre5500g1ww My washer has started leaking from behind the lid after the laundry has finished spinning and the machine is off. I was able to see that the water inlet hose Diagram 01, part #803, was dripping water. I unscrewed it to check for lint buildup but nada. Could the problem be caused by the probe sensor atc, part #25? If I do need to replace this part how difficult is it to pull the cover assembly? Thanks for your help.
1 Answer Janet, With the water tube leaking the issue would be more likely a faulty water valve that is not fully seating causing this issue to occur. The part number for the water valve is WH13X10024. Read More...
Debbie September 26, 2014 for Model Number Wjre5500g0ww Hot water wash will not work. I already replaced the water inlet valve, verified that hot hose went into hot valve, and that when I disconnected the hose the water comes out hot with high pressure. Any other suggestions? I appreciate any help.
1 Answer Debbie, You will want to check the ATC sensor probe and make sure that it is good. To check you will need to do a resistance check and the resistance should be 50K ohms at 77 degrees. If the sensor WH12X10251 checks ok then the issue will be the control board WH12X10404. Read More...
Luis F. September 01, 2014 for Model Number GGW9200LW0 The softener stays in the tray in the machine.
1 Answer Hello Luis, I'm sorry but I cannot look up dispenser parts for your washer with the model number posted. It is actually the dryer model number. The issue sounds as though you have a bad water valve or dispenser motor, depending on the design you have. If you could please verify the model number from the washers' I.D. tag, we will be more than happy to assist you. Thank you for your patience and understanding in this matter. Read More...
Jim Was June 25, 2014 for Model Number wprb9220 When my washer is calling for hot water the hot water only opens for about 12 seconds and keep filling the rest of the way cold. Even in the hot cycle the water is too cold.
1 Answer Jim, The most likely cause for the unit switching to cold water when you are looking for all hot would be a faulty thermistor which is part number WH12X10251. Read More...
1 Answer Gloria, the only way to obtain the on switch or any of the switches on the control is to order the control assembly part number WH12X10614C. Thanks. Read More...