Amber January 04, 2014 for Model Number wwse5240g1ww Hello, I am stumped on what could be wrong with my washer. I havelooked at everything I could think of and cant figure it out....it washes fine when empty but when you put clothes in and do a wash cycle it spins out of control...any ideas on what this could be? please help
1 Answer Amber, Most likely the issue with the unit is the washer apron is bent causing the unit to get off balance and spin out of control. The part number that you would need is WH49X20925. Read More...
Jo October 28, 2013 for Model Number WSERE526F0WW GE washer occasionally stops randomly in fill/wash/rinse cycles. Field service mode shows thermistor error. Do you recommend the control board (AP3892692) or thermistor (AP3794965) be replaced? Thanks.
1 Answer Jo, You would want to check the sensor probe to make sure that it is not showing open. If it is then it would need to be replaced. The thermistor would be the most likely cause of failure. Read More...
Tyler August 26, 2013 for Model Number WHRE5550K1WW Washer lights are flashing and nothing will work. Just replaced the funnel shower (Sears part #803), but it did not have a hole for the probe sensor (#25). What does this sensor do? I am sure this could be the problem.
1 Answer Tyler, The funnel shower WH41X10206 should have a hole in it for the water temp sensor which is what the probe is for. The sensor will allow the unit to sense the water temp coming into the unit and adjust it according to need. If the sensor is not connected then the unit will recognize this and not allow the unit to operate. Read More...
Bonnie March 25, 2013 for Model Number WPRB9220D1WW, SL128640g Do I have to get a new panel if the start button doesn't work?
1 Answer Bonnie, the start button is only available with the backsplash asm part number WH12X10316. Sorry about that! Read More...
Frank L January 05, 2013 for Model Number WHDSEC820COWW I have a top load GE washer about 5-7 years old. Model is discontinued but parts still available. My washer stopped working after making horrible noises. Motor wouldn't make anything move ( this was original 2 speed clutch motor). Yesterday I replaced it with a new 2 speed clutchless motor and did all the rewire according to directions. It works fine thru all the cycles until the final spin where it won't spin unless almost empty.The clothes are soaking wet so I remove most of them and I get it to spin then open lid and throw in a few pieces at a time and allow it to drain some of the water until all the clothes are spin dried. Could it be the control panel or the water fill tube sensor)???
1 Answer Hello Frank, You will need to install the correct motor assembly for your unit for it to work properly. The correct motor for unit is a motor and clutch kit 2 speed WH49X10035. Read More...
Dan L September 11, 2012 for Model Number WJRE5500GWW With my scenario, do you think I need the board or the thermistor? Below is original question and your answer. Please advise Thanks, Dan Is this part the start button? After you set your settings and push this button does this activate the water to start filling the machine. Ours works sometimes and other times we can't get it work at all. You push to start and nothing happens or you get lucky and it starts filling. Asked by Dan for Model WJRE5500GWW Hello Dan! No, part number AP3794965 is the atc probe thermistor. The start button/switch is on the board AP4380181. Thanks! Read more: http://www.appliancepartspros.com/questions-for-GE-Probe-sensor-atc-AP3794965-qid65717.aspx##ixzz26CGOqu1C http://www.appliancepartspros.com
1 Answer Hello Dan. Based on the information you provided, it sounds like the control board WH12X10404 is bad and will need to be replaced. Read More...
Dan September 11, 2012 for Model Number WJRE5500GWW Is this part the start button? so after you set your settings and push this button does this activate the water to start filling the machine. Ours works sometimes and other times we can't get it work at all. You push to start and nothing happens or you get lucky and it starts filling.
1 Answer Hello Dan! No, part number WH12X10251 is the atc probe thermistor. The start button/switch is on the board WH12X10404. Thanks! Read More...
1 Answer Hello Pat! According to the picture we have available the probe sensor atc WH12X10251 wiring is black and white. Thanks! Read More...
John October 05, 2011 for Model Number WBB4500G0WW Still in response to my earlier question on when warm water is entering the GE washer I am now hearing a low hum (where as before i did not hear any noise), also, no noise if just cold or just hot... and the water presurre is the same still... what is causing the hum? or is this something that just happens over the years... it is about 4-5 years old.
1 Answer Hello John. Yes, the valve will make a humming noise the older it gets. You can replace the valve and fix the problem your having with the unit. Hope this helps. Read More...
John October 04, 2011 for Model Number WBB4500G0WW When water enters if the setting is cold or hot I everything sounds fine, but when on warm water does enter but I hear a low level hum or vibration... Is this the sensor acting up?
1 Answer Hello John. If the unit is limiting the flow of hot or cold water, the low hum is normal. If the water pressure on the cold or hot side is low, and it used to be high, you will need to replace the water valve WH13X10024. Hope this helps. Read More...