Jesse September 05, 2012 for Model Number 6364851644 My washer will run through the wash cycle, but when it comes time to drain it just buzzes loudly and won't spin. Once I get enough water out it will start spinning, but the humming sound continues while spinning. I think it is the pump since it will spin in the drain cycle.
1 Answer Hello Jesse. Based on the information you provided, either the pump is bad or it is clogged. If not clogged, you will need to replace the pump WH23X10030. Read More...
George August 01, 2012 for Model Number older model ge top loader(pump ap3160348 We start washing cycle with 12 minutes it goes thru that cycle to 9 minutes and then to 6 minutes where at the end of cycle it sounds like its pumping water out of tub and then stops and shuts off....It has not rinsed or gone to spin cycle....We manuel put machine on rinse cycle and it completes it but still want go spin cycle....We let machine cool down for a few minutes and put it on manuel spin and it does a complete good job...Is it the pump getting hot and shuts down or is it one of water hoses plugged...I took off pump and checked and hoses but did not take hoses off completely...Does the pump over heat and after a cool down period works ok....Thanks for the help and answer to my questions....Sorry dont have the model handy....George
1 Answer Hello George. Either the pump is failing or the motor on the unit is failing and causing the issues you are having. You will need to check and see which part is bad on the unit. Read More...
Jerome August 01, 2012 for Model Number WHSE3100A0WB My washer fills up and agitate like it suppose to, but when it comes to spin cycle it don't spin out. I took pump off and drain the standing water out of the tub. I check pump for clogs and check the pump with 120V to make sure the pump was fine and it was. What should I check next to see why water won't spin out?
1 Answer Hello Jerome. You need to test for power coming to the drain pump. If there is no power there, you need to make sure the lid switch WH12X10141 is good and if so, you may need to replace the control board WH12X10176. Read More...
Jonathan July 13, 2012 for Model Number WHDSR417DOWW Hello, My washer works fine until it gets to the drain/spin cycle. It wont drain or spin. It has been doing this for a while but we usually just pull the drain hose and blow into it and it will work like the pump is clogged. Last night it stopped working and I blew into the hose and nothing happened. Usually we can hear the pump turn on but I dont hear it any more. Should I just replace the pump? Thanks!
1 Answer Hello Jonathan, You need to remove the hose from the outer tub to the drain pump. If there are no restrictions, you will need to replace the drain pump WH23X10030. Read More...
Julio May 18, 2012 for Model Number wcsr2090g3ww My washer is not draining nor spining with water or when loaded. I test it with no water and the spining cicle worked as normaly but while spining I put water in and it stopped. What shoud be the problem?
1 Answer Hello Julio. Based on the information you provided, it sounds like the transmission WH38X10002 is the problem with the unit. Make sure the clutch and the belt are good. If so, replace the transmission. Read More...
Amy April 18, 2012 for Model Number WH23X10013 I am replacing the pump (model # above) on my GE Profile washing machine. I can unhook everything except the wires from the old pump. I've tried pulling and squeezing in every direction. It's probably very easy, but I can't do it! What is the trick?
1 Answer Hello Amy. The wires going to the pump assembly pull off the spades. You may need to use a pair of needle nose pliers to pull the connectors off the pump WH23X10030. Hope this helps. Read More...
David April 07, 2012 for Model Number wpsq3120t5ww I just asked the question about where the green wire goes that I found when I was hooking the pump back up on my washer. It is not from the pump. It is in the wiring harness with the two wires that hook to the pump. I know that green is ground but do not see any where that it can hook. It has a female end on it.
1 Answer Hello David, There is normally a ground spade attached to the housing for the ground wire to attach to, but if there are none, I would just insure that it is in a position that it cannot get close to any "hot" wires and short them out. It will work fine. Read More...
David April 07, 2012 for Model Number wpsq3120t5ww I was just putting a new pump on my washer and when I went back to connect the wires to the new pump I noticed that there are three wires. I have the two connected back to the motor that was on it when I took it apart but was wondering where the green one goes.
1 Answer Hello David, Green is always chassis ground. If the green wire is from the new pump, the other end connects to the body of the unit. Read More...
Adrie March 31, 2012 for Model Number wwre5240d0ww hi i have a problem with my washer and wondering what can be the problem.the washer started normal but when it went to the rinse cycle it stop .wont rinse so my washer still has water .i can hear a click when i try to put it to rinse. can u please help. thank you
1 Answer Adrie, If there is wash water left in the tub, your first check should be the drain pump WH23X10030. You'll need to remove power and the front panel, using a putty knife to press in on the release clips between the top panel and the front panel seam, and lean the front panel towards you at the top, then lift it off the bottom tabs. Disconnect the hoses from the pump, and check to see if it is clogged with a small article. You can attach a 120 VAC power cord to the terminals and check to see if the pump motor runs, when you plug the cord into an outlet. From there, if alls OK, we'd need to check the lid switch and Timer. Good Luck and Thanks Read More...
Ashford March 19, 2012 for Model Number S20000D2WW I disconnected my drain pump to unclog it. I drained the machine and put the pump back into place, but I don't remember how the wiring was connected. There are only two connections to the pump, a black wire and red/white wire. Which side do I connect each to?
1 Answer Hello Ashford. The polarity of the wires on this ac motor makes no difference. You can swap the wires and the motor won't notice at all. Hope you have a great day! Read More...