General Electric Washer Pump

The Drain Pump is an OEM part for GE washing machines. It is responsible for removing water from the washer's tub at the end of each wash cycle, ensuring that your laundry is properly drained before the spin cycle. This pump helps to prevent water from sitting in the tub, which can lead to mold and mildew.

Symptoms of a bad Drain Pump include:

• Water not draining out of the washer, leading to stagnant water pooling in the tub.
• Unusual noises during the drain cycle, indicating a struggle or failure to operate.
• The washing machine stopping abruptly before or during the drain phase.

Causes of a bad drain pump can include blockages from small garments or debris, mechanical failure from wear and tear, or electrical issues that affect the pump's power supply.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The GE pump is an OEM replacement part responsible for removing wastewater from the washing machine during the drain cycle. It pumps out the soiled water from the washer's tub, ensuring that it is expelled through the drain hose and into the plumbing system or utility sink. The pump consists of an electric motor and an impeller that move the water effectively.

Causes of a bad pump can include clogging from debris or lint, wear and tear from regular use, or damage to the pump impeller or motor. Exposure to harsh chemicals or overloading the washer can also contribute to pump failure.

Symptoms of a bad pump include:

• Water not draining from the washer
• Unusual noises such as humming or grinding during the drain cycle
• Error codes related to drainage issues
• Water leaking from the bottom of the washer

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Drain Pump Assembly is an OEM part for GE washing machines. This assembly is responsible for removing water from the washer during the drain cycle. It ensures that water is efficiently pumped out of the washing machine and into the household drain, allowing the appliance to proceed through its wash and spin cycles without issues.

Causes of a bad drain pump can include blockages from debris or lint, electrical failures, or wear and tear from regular use. A malfunctioning pump can lead to drainage issues, leaving water in the washer and preventing the machine from completing its cycles.

Symptoms of a bad drain pump assembly include:

• Water not draining from the washer
• Unusual noises during the drain cycle
•  The washer stopping mid-cycle due to drainage issues
• Water leaks from the pump area

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This drain pump assembly removes water from the washer tub during the drain portions of the cycle, helping ensure proper rinsing and spinning and preventing water from remaining in the machine after a wash.

• Pumps wastewater from the tub through the drain hose to the household standpipe
• Common failure symptoms include the washer not draining, water left in the tub, loud humming or grinding from the pump area, or leaks around the pump/hose connections
• Restores proper drainage to support effective spin performance

• Disconnect power and turn off water supply before servicing; bail or wet-vac any standing water
• Keep towels or a pan handy to catch residual water when removing hoses
• Mark hose positions and transfer any existing mounting brackets or connectors from the old pump as needed
• Inspect and reseat hose clamps and the drain hose to ensure a watertight seal before testing

This pump and brake assembly drains water from the tub and applies the basket brake in your top-load washer. Replacing a worn assembly restores proper draining and a safe, prompt basket stop between cycles. What it does

• Pumps water out of the washer during drain and spin phases
• Applies the brake to stop the spin basket between cycles or when the lid switch is activated
• Helps reduce extended coast-down and stopping squeal
• Typical symptoms: standing water, slow/no drain, leaking at the pump area, basket coasts too long or squeals when stopping

• One pump and brake assembly

• Disconnect power and water supply; drain remaining water from hoses before service
• Access from the washer's underside; support the unit securely
• Transfer existing hoses/clamps to the new pump and secure all connections; if belt-driven, verify proper belt routing and pulley alignment
• Run a brief fill/drain test and recheck for leaks and proper basket stop

The DRAIN PUMP is an OEM component specifically designed for GE washers. It is located near the base of the unit and functions to remove water from the wash tub at the end of cycles. The drain pump works vigorously to expel soiled water through the drain hose for hygienic cleaning.  

Symptoms of a bad drain pump include:

• Water remaining in the tub even after cycles have finished running  
• Drain hose that is not effectively carrying away water
• Strange gurgling or churning noises coming from below the unit
• Possible leakage from seals or connections near the drain area

Causes can include internal blockages from built-up debris, wearing of impeller seals or motor, or physical damage impairing pump functionality.

Replace yours today with this genuine OEM GE part for thorough water extraction and machine drainage after every load. This GE replacement part is compatible with Hotpoint, RCA, and select Kenmore models.