Bob June 27, 2012 for Model Number WDSR2080G2WW Washer will not advance through the cycles. Could this be the timer unit?
1 Answer Hello Bob. If you can manually advance the timer on the washer and it works, but does not on it's own, you will need to replace the timer WH12X10338. Read More...
1 Answer Hello Bill. Pull out on the knob. On the back of the knob, there is a small plastic clip. You will need to use a pick tool or an ice pick and pull the clip from the knob. Once you pull out the clip, the knob pulls off the timer WH12X10338 shaft. Read More...
Courtney April 10, 2012 for Model Number 110.22832100 Sears Kenmore GE My Kenmore/GE top load washer will fill and agitate/wash the entire cycle but when it comes to the rinse cycle it just stops. We have checked the drains and everything is clear. There are no belts on this washer, so that can’t be it. We have tried other wash settings and the same thing happens when it gets to the rinse cycle. I have also checked the lid to make sure that the lid switch is clicking and securely closing and it seems like it is. Could this be the timer?
1 Answer Hello Courtney, This sounds to me as though the cold water valve 285805 has failed, unless the cold water got turned off without your knowledge. If you change the water valve, be sure to unplug the unit and turn off hot and cold water before removing the hoses. Read More...
Gene Donnelly March 27, 2012 for Model Number WLSR2000G2WW I am attempting to troubleshoot my washer. The timer will move on the left side for delicates, but does not perform functions that the timer says it should. The right side of the timer does not move properly, so the water fill does not shut off, and has flooded the floor. Before I purchase a new part, I would like to be certain what part is needed? Do I need to replace entire control board? Thanks, Gene.
1 Answer Hello Gene, After studying the wiring diagram, the only thing in the circuit that isn't used in the delicate cycle is the timer WH12X10338. Read More...
Danny M March 24, 2012 for Model Number wcvh6800J1mr My GE front loader washer will start to wash and wash for a short time them just stop and unlock the door. I can hit start again and it will wash again. It will not move to the next cycle. I can manualy switch to the next cycle and it will rinse and spin. I have cleaned the filter and did a 30 sec reset, but no good. Do I need a new timer or what should I do next? Thanks for any help
1 Answer Danny, You don't really have a timer, you have an electronic control boardWH12X10468 and you should eliminate other possible causes,before you replace it. It could be as simple as a loose connection at the board or water level switch. The information we sent you, should be a big help, and get you up and going. Thanks and Good Luck Read More...
Clyde H. February 20, 2012 for Model Number gjs122080h2ww The washer will go through the wash cycle but will not spin. On the wiring diagram a line switch is shown. Where is this switch located?
1 Answer Hello Clyde. It sounds like you are talking abou the lid switch assembly WH12X10531. If bad, it will prevent the washer from spinning. Hope this helps. Read More...
Lisa January 11, 2012 for Model Number Wdsr2080g2ww When I set my washer knob to the correct setting it just washes and won't move any further if I move it maually it works but it is stuck and won't cycle thru the whole wash. Could this be the timer?
1 Answer Hello Lisa. Yes, based on the information you provided, it sounds like the timer WH12X10338 is bad and will need to be replaced. Hope this helps. Read More...
Fern January 08, 2012 for Model Number GE My washer timer knob just spins and wont start the washer. I took the timer knob off and it is ok, however the part the timer knob goes into is broke. What part is needed?
1 Answer Hello Fern. Based on the information you provided, it sounds like the timer WH12X10338 is bad and will need to be replaced. Hope this helps. Read More...
Ddazzle August 24, 2011 for Model Number wlsr4460g0ww I can't find this model to order a timer. The timer has the following Numbers on it 7023b GE 175D5749P005 M298 and Kingston 71595-A04145, can you help me find the correct timer? Thanks, Dennis
1 Answer Hello Dennis! Model wlsr4460g0ww seems to be invalid. We have tried checking on the GE sites as well and they do not recognize this model. The closest model I could locate is WJSR4160G0WW. Please double check your appliance model number and also supply a serial number for further research. Thanks. Read More...
Missy August 03, 2011 The knob on the timer dial feels like it is stripped and wont turn the timer dial. However, if I turn the lower dial manually it goes through the cycle fine. Is this a knob problem or timer switch?
1 Answer Hello Missy. You will need to remove the clip from the back of the timer knob WH01X10310 and see if the teeth are worn down. If so, you will need to replace the timer knob. Hope this helps. Read More...