Kevinrusnak@Comporium.Net January 11, 2015 for Model Number GE Profile "Energy Star" model WPRE8150K2WT Greetings: I have a GE Profile "Energy Star" model WPRE8150K2WT that will not put enough water in to fully cover clothes. This is the way it has allways been since new. I know these new machines are made this way, but the wife has to add water to cover clothes. QUESTION: how do you adjust the water level switch screw to increase the water level a few inches or more? (clockwise or counter-clockwise to increase)? Thanks in advance for your advise!
1 Answer Kevinrusnak, Unfortunately there is no way to adjust the water level to the unit as this is preset by the factory and would have to be calibrated to change the water level settings. Read More...
1 Answer Hello Jose. Check the lid switch and water valve on the washer. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Melissa May 18, 2014 for Model Number S1070A3WW My washer keeps filling up and won't switch over to agitate once in a while. What part would I need to fix it? I was told either the water level sensor, or the water level control switch.
1 Answer Hello Melissa, This would be the pressure switch but I cannot give an accurate part number without the valid model number from the units' I.D. tag. You can re-post with this information or give us a call at 1-877-477-7278 and one of our representatives can look the part number and pricing information for you. Read More...
Erik April 28, 2014 for Model Number wcsr2090d5ww Sometimes the machine will not agitate or fill when rinsing. Now when I move around the load size switch back and forth it will work just fine. Do I need a new load selector switch??
1 Answer Hello Erik. Yes, it sounds like the pressure switch WH12X10065 is bad and will need to be replaced on the unit. Read More...
Dale D April 21, 2014 for Model Number GE wbb2090f1ww My G E washer Model Number is WBB2090F1 goes through it cycle's and does not spin out. if I unplug the washer and plug it back it spins and seems to go through cycles fine, and also seems to work better in the delicate cycle. It also seems to be pumping water out as it goes through its spin cycle and dose not stop pumping water out until washer stops in it final cycle. This is the final scenario wet clothes that have not been spun out. Could this be the water pressures switch or the washer timer.
1 Answer Dale, Based on the information the issue sounds like the timer contacts may be sticking when the unit goes to the spin cycle. Read More...
Bob April 01, 2014 for Model Number WWSR2090T GE Washer Start any wash cycle and water flow does not stop...machine still agitates etc...but water keeps flowing. Operate program/timer control switch but water does not stop. I unplug machine from power and water stops. I can blow (very slowly) down pressure line on water level switch. Should I replace switch or is it a control issue?.
1 Answer Hello Bob. Make sure the air dome is not clogged. If not, and the hose is good, you will replace the pressure switch on the unit. Read More...
1 Answer Amrit, The model number is not showing as being a valid model but Gibson was manufactured by Frigidaire and the GE part would not work for the model. Read More...
Rodney C January 20, 2014 for Model Number gcwp1000moww GE import model to rep of Panama. All wash levels are low, but rinse/soak level is almost nothing (2 liters or so). Looked at water level switch - no adjustment on it. Is it the water level switch, timer or USA saving water regulations??
1 Answer Rodney, Unfortunately we would not have any information on export models to be able to assist. Read More...
Nick December 05, 2013 for Model Number S1070a5ww I am replacing my water level switch. Before I put the washer back together, I wanted to clean the air dome on the side of the tub. Can it be removed or what is my best option?
Jim October 20, 2013 for Model Number maytag mvwc3oov Water level control works very hard from low to mid level, good to high and good back to low level. Counter cloockwise it works fine.
1 Answer Jim, You will want to pull the knob off the unit and check to make sure that there is nothing causing the switch to jam behind the knob and if that checks ok then you would want to replace the water level switch WH12X10065. Read More...