Mike May 10, 2017 for Model Number LBN22515ST What ice maker assembly do I order for this model refrige?
1 Answer Hello Mike. You will need to contact the manufacturer and order LK45C to install an icemaker into this model. Thanks. Read More...
Max April 27, 2017 for Model Number Aeq36756901 Just replaced my old Lg Ice maker (Aeq36756901) because it was not dumping the ice. My new one won't dump the ice either. Could it be the motherboard?
1 Answer Hello Max. Make sure the icemaker is turned on and the temp is 0 to 5°. If so, then the new step would be the board. Thanks. Read More...
Mina D March 20, 2017 Icemaker not making. It tripped the circuit breaker and after that stop making ice. What could be the problem?
1 Answer Mina, For this issue it would most likely be caused by a faulty icemaker with the icemaker not working after a power surge. Read More...
Gail M. March 18, 2017 Just bought a LG last week and the ice maker is not working right. I received it last Saturday and it has not even covered the bottom of the tray. Please advise. Thanks
1 Answer Hello Gail, You will first need to check the operating temperature of the unit with a freezer thermometer. The icemaker has to achieve 20°F to cycle. If this is occurring check for water in the tray. If the tray is full and the temperature is sufficient, replace the icemaker AEQ36756901. Read More...
Rosario February 01, 2017 for Model Number LG LFX25960ST Ice maker not working and making a pinging noise, took it off to check for ice inside the gears, none, put it back, no noise no water and no ice...
Robin F January 22, 2017 for Model Number LG LFX25973ST The ice tray in the door to the fridge broke. Cracked right through the tray. Is there anyway to order just the ice tray to replace? I can't find a part number or correct tray anywhere, there are 14 cubes, 2 rows of 7... help???
1 Answer Robin, The part number that you will need to get will be the the icemaker kit part number AEQ73110205. Read More...
Greg J January 05, 2017 for Model Number LMX25981SW The ice maker works fine. The refrigerator water inlet valve went bad, so we have lived with poor water pressure for about a year. During this time we lost the water line cover for the ice maker but never noticed. Now that the inlet valve has been replaced, the water pressure is so great that when the water fills the ice maker, water splashes all over because it is missing the plastic cover where the water comes in. Are you able to order that little piece of plastic separately, or do you need to order the complete ice maker assembly kit.
1 Answer Greg, The plastic cover is not available as a separate part and you would need to get the icemaker assembly for this. Read More...
Bob December 24, 2016 for Model Number LSC27931ST When water fills tray it also leaks out by arm and freezes is there a repair kit for ice maker. If we brake ice off arm it makes ice but then leaks out on to arm again
1 Answer Bob, The part number for the icemaker on your unit will be part number AEQ36756901. Read More...
Jim November 03, 2016 for Model Number 79576203901 I replaced Ice maker, fill tube and fill valve, and fill tube still freezing, so thought the freezer gasket could be bad, So I cleaned it and the ice maker worked for 2 days, then line froze, so I replaced gasket, fill line freezing again
1 Answer Hello Jim. Maybe the freezer is to cold. It should be 0 to 5°. If it is too cold, it can cause the fill tube to freeze up. Also, make sure the water pressure coming to the refrigerator is good and not to low. Read More...
Dale October 15, 2016 for Model Number Kenmore 795.79782.901 Part Number: AP4442284 MFG Part Number: AEQ36756901 Made by: LG Are there any adjustments to lengthen the water valve open time on this unit other than the small, medium, large cube size switch. My unit fill cycle only stays on about 3 or 4 seconds which is barely enough time to fill the first 2 ice cube slots.
1 Answer Dale, The adjustment that shows small medium or large is the only adjustment on the icemaker. It sounds like you may have low water pressure getting to the valve or the valve is faulty. Check the dispenser to see if it is flowing slowly, should fill 8 ounces within about 15 sec. If it does not fill properly then the issue will be a water filter that may need changed. If it does fill properly then will most likely be the water valve that is the issue. Read More...