John March 01, 2014 for Model Number 79571302010 Replaced water filter, now ice maker is making ice very slowly. Any help appreciated.
1 Answer Hello John. You need to make sure the freezer is between 0 and 5° inside the unit. If not, it will not produce ice properly. Read More...
Laurianne January 30, 2014 for Model Number AP5325806 Can you get just the ice cube tray and not the whole kit for the ice maker??
1 Answer Hello Laurianne. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Juanuta October 04, 2013 for Model Number AEQ72909603 I need directions for removing and replacing icemaker AEE72909603.
1 Answer Hello Juanuta, Remove the two screws securing the ice maker to the ceiling of the unit. Slide it forward and disconnect the wiring harness. Install the new one in the reverse order. Read More...
Patrest@Frontier.Com March 08, 2013 for Model Number 79571016010 Ice Maker problem. Maker was in off position, as I do not use lot of ice. Turned on and did not make ice. Changed water filter (Indication Light for Change not on), as it had been four months and thought that might be the problem. No ice made for over two days. Refrigerator about three years old. Do I need to order a replacement ice maker?
1 Answer Patrest@frontier.com You will want to push the test button on the bottom of the icemaker to see if it will cycle. If the icemaker does not cycle then you would need a new icemaker. If it does cycle then you may have a frozen fill tube and will have to clear the fill tube to get to work. Read More...
Dee January 27, 2013 for Model Number LFC25770/05 I need to replace my icemaker with part AEQ72909602 as the ice is sticking in the tray and not dumping. This is a French Door with Freezer on the bottom and no in door water and ice, you pull out the drawer and reach in to get ice. Is there a video on how to take the drawers out and replace this icemaker? I'm concerned about getting the doors back on. Does this icemaker hood on to something in the back with just two screws in the front? I really could use instructions on how to replace is there any way to get them?? Thanks
1 Answer Hello Dee, Unfortunately there are no instructions for replacing icemaker. Normally you do not have to remove the shelves. The top shelf can be removed by clips on the side or just lifting out. If you remove the 2 screws in the front you just have to pull the icemaker down and forward to release from ceiling. Once you have the icemaker loose disconnect wire harness, plug in new harness and put icemaker back in. You will put the back in first and slide toward rear. Put screws in and cover back on. Read More...
Lynne November 05, 2012 I have had the icemaker replaced once and the technician out here a couple times regarding this icemaker, The first time it made such an awful noise when it would dump the ice that it would wake you up at night. Now this time the sensor arm is just flopping down and I can't get it to go up? Is there anything I can do to get it back to where it goes? or do I just have to repalce the entire icemaker again??
1 Answer Hello Lynne. Based on the information you provided, you will need to replace the icemaker AEQ72909602 in the unit. Read More...
Jeff September 08, 2012 for Model Number 795.71303 This is Jeff again... sorry if I wasn't clear the 1st time but the feeler arm is "floppy" .. which I why I think it might be broken. I've already ordered a new icemaker kit, it seems easy to install with just 2 screws and plug-in, is that right?
1 Answer Hello Jeff, You are correct. Some models actually have three screws but it is still a cut and dry repair. Read More...
Jeff September 08, 2012 for Model Number Kenmore 795.71303 The feeler arm on my icemaker is permantently in the "down" position. I've tried turning the icemaker off and then on with no help, so I assume it's broken and I will need to replace the icemaker. It almost seems too simple to replace (2 screws and a plug-in); is there anything else I need to know? Does the replacement part come with instructions?
1 Answer Hello Jeff. If the icemaker is new and does not work, replace the control board on the unit. Read More...
Peter August 27, 2012 for Model Number aeq72909602 manufac. part# Just installed new ice maker and it doesn"t work. Part did not come with directions. Plastic arm seems to be stuck in the up position.
1 Answer Hello Peter. The plastic arm should be in the up position on this one. It has to get cold before it will cycle. If the icemaker is new, and the unit does not cycle after 4 to 6 hours, replace the main control board. Read More...
Jack August 08, 2012 for Model Number LG LBC22520SW frig, Ice-maker AEQ72909602 Ice-maker has made ice in the tray but does not dump it, even when I pres the test button for 10 seconds, so i need a new ice-maker. But until it arrives and I get it installed, is there a way to manually make the broken ice-maker dump and refill?
1 Answer Jack, Sorry, but No, there isn't. If the icemaker wont advance, harvest, and fill in the test mode, There's no manual way to advance the cycle. Sorry. Thanks Read More...