Eric T. October 14, 2017 for Model Number LFX31925ST My ice maker stopped making ice all of a sudden. It's 3 years old. How do I trouble shoot what is causing the issue?
1 Answer Eric, Try to push the test button to see if the icemaker will cycle. If it does then the issue will be the thermostat on the icemaker which would require a new icemaker. If it does not then this could be a faulty main board not sending power to the heater or to the icemaker module. Read More...
Ronald October 12, 2017 for Model Number Kenmore Elite My ice maker stopped dumping ice among several other past issues.( replacement of bottom cover of condenser coils for error code regarding a faulty fan and heater design) in freezer. I recently replaced the icemaker AEQ73110206 with (Now AEQ73110203) in my 2yr old fridge. The unit fills makes ice but in the dumping rotation stops shortly after it begins the rotation. When I press the reset button it finishes the cycle and refills again. I come back later to find it's made ice again but it's stopped in the same place in the rotation cycle. I once again have to press the button to complete the cycle. Needless to say very annoying for what's supposed to be an "elite" product.The original ice maker was doing the same thing in which I read suggestions to replace the ice maker. When I replaced it the new one is doing the exact same thing. Any help in resolving this would be appreciated. Ronald
1 Answer Hello Ronald. If the icemaker is new, then it sounds like the main board on the unit may be bad and will need to be replaced. Thank you. Read More...
Ann E September 30, 2017 for Model Number 79572063315 My Kenmore refrigerator has been leaking water in the ice dispenser housing. When the ice tray empties, water is overflowing at the refill hose. That water runs inside the compartment and causes ice build up. I have to chip it out every day and wipe water out of the gasket at the bottom of the door. I tried replacing the water inlet valve. However, now the thing is actually leaking worse with the new part than it was with the old. What are the chances that replacing the ice maker assembly will actually resolve this issue? If the chances are high, can you give me the part number? I don't see a video on how to replace the ice maker. Is there one out there that I just haven't found?
1 Answer Ann, This issue sounds more likely that the water valve is not closing and would need to replace the water valve assembly for this issue. Read More...
Jerry September 08, 2017 for Model Number LFX28968ST01 Ice maker making loud clicking noise when trying to dump ice and gets stuck in what ever position it is in at that time and finally stops clicking but still stuck. Do I need to change it out with a new part or model? Thanks for your help, Jerry
1 Answer Jerry, With this issue it does sound like the icemaker assembly is faulty and would need to be replaced. Read More...
1 Answer William, If you remove the ice bin there will be 3 or 4 screws in the panel behind the bin that will need to be removed and take the icemaker out of the unit. Read More...
Windowman July 14, 2017 for Model Number LFX31925ST The sheathed wires from the motor area to the ice tray has burned though the wire is still attached. I have decided to replace unit for safety if no other reason.
1 Answer Windowman, The part number you would need for this would be the dispenser motor and icemaker assembly EAU60783827. Read More...
John H June 11, 2017 for Model Number LFX31925ST/06 Ice maker making weird/loud knocking noice in the motor housing. I suspect the new unit needs to be replaced. How do I get to and disconnect the wiring harness. Model # :FX31925ST/06
1 Answer John, First remove power to the refrigerator, then open the door and ice maker compartment. Remove the four(4) screws that secure the assembly to the door panel (2 on the bottom, one in the center and one above the ice maker). Grasp the bottom of motor cover assembly and pull out slowly and carefully. Disconnect wire harness from wall of compartment. ***Make sure that the motor housing is taped to the mold, if not positioned correctly the cover will not fit.*** Release the wire harness connections on the back of the housing and remove the ice maker. Reverse the procedure and check the ice maker operation. Read More...
John G June 05, 2017 for Model Number LFX25974ST My icemaker is still is making ice but only making a little less than half a bin. Do I need to replace unit? I took it apart yesterday and let it thaw out thinking that something was frozen, but same situation
1 Answer John, Yes, you'd want to consider replacing the ice maker assembly as the first repair option. That style ice maker has several "sensors" that control the operation and they can and do fail, or operate intermittently. Read More...
John April 13, 2017 for Model Number LFX28978ST Ice maker needs to be replaced. How do I remove it to check the secondary plug for the correct amount of wires? I removed three screws to loosen it from the main panel behind it, but don't see plugs.
1 Answer John, Remove the four(4) screws from the main panel on the back of the compartment. Grasp the bottom of motor cover assembly and pull down and out slowly. Disconnect wire harness from wall of compartment. *** Make sure that the motor housing is taped to the mold, if not positioned correctly the cover will not fitproperly. *** Then dismount the ice maker from the assembly (3 screws). Reverse the procedure and check the ice maker for operation. Once you remove the rear panel, you'll have access to all the wire harness connections. Read More...
Sharon S. March 08, 2017 for Model Number LFX31925SW/00 Makes ice but it won't drop the ice.The little flapper won't open and it doesn't make any noise.
1 Answer Hello Sharon, If the connections are good at the door hinge the issue will most likely be the dispenser board EBR60388502 or one of the actuator switches, 6600JB3001C or 6600JB3001F. I'm sorry but this part 6600JB3001F has been discontinued by the manufacturer and no satisfactory substitutions have been provided. Thank you for your patience and understanding in this matter. Read More...