1 Answer Hello Jim. If your sure the water valve is good, and there is water coming to the unit, you will need to order and replace the board on the unit. Read More...
G May 03, 2016 for Model Number LG WM0642HW The washer was not receiving any hot water so I replaced the hot water inlet valve after verifying the water pressure from the hose was sufficient. Now, the hot water flows even during the cold water wash. The water stops when the washer is unplugged. Could this be a faulty hot water inlet valve or ????.
1 Answer G, With the unit only putting in hot water then it would be more likely that the issue will be a faulty control board that is sending power to the hot water side but not the cold water side. Read More...
John M March 04, 2016 On normal cycle to water level is to high cauising the door to leak. Machine fills up to about 2 inch from top of door.
1 Answer John, With the unit filling too much then you will want to check the pressure hose to make sure that it is not clogged and if this checks ok then the issue will most likely be a faulty pressure switch. Read More...
Donnie October 11, 2015 for Model Number lg front loader mod # wf438aarxaa Just replaced flange shaft assemble, bearings, seals, shocks etc. having problem with over filling. Need to know if there is a small hose connecting to the water level switch. There is a fitting on it for one. Also had problem previously with not getting the softener flushed in . Suspect water inlet valve assembly for that.
1 Answer Donnie, The hose that would go on the water level switch would be part number DC97-14545F. The issue with the fabric softener would most likely be the water valve. Read More...
Jimi September 08, 2015 for Model Number Lg wm3987hw I recently replaced the drain pump, but when I got everything back together, it wouldn't fill with water. A little came through, but then just stopped. I have checked the hoses and the filters and there is no debris. What could it possibly be?
1 Answer Jimi, You will want to check the drain pump for 120 vac getting to it when the unit goes to drain. If there is not 120 vac then the control board would be the issue. Read More...
Marta August 25, 2015 for Model Number wm2250cw Hello! My washer water level is really low and cloth is not cleaning even when I use water plus option. There is no error showing. I recently changed the water inlet valve and the thermistor. But the water level didn't increase. Could be water pressure switch?
1 Answer Hello Marta. Yes, if could be the switch or the hose on the unit. You will need to check both of them. Read More...
Tarn March 15, 2015 for Model Number WD-10485TP My machine will not spin. It drains fine, agitates a little bit never 'gears up' and starts really spinning. I thought it was the pressure sensor. So I replaced it. The original part was a 6601EN1005A. The people I ordered from sent me a 6601EN1005B. I have been told that this part is definitely compatible. I have cleaned all piping and even taken the pump apart and cleaned that. I have ensured that the machine is extremely level. Still nothing. The machine does spin sometimes with a really really large load and after a rinse cycle but never in the final spin for normal sized loads. I read somewhere that this means the motor is at fault as it supposedly cannot get up to speed for the final spin. However if I put it in diagnostic mode I can't get it up to a full spin with three button presses. Any idea what the problem might be?
1 Answer Tarn, Unfortunately we do not have any technical information on this unit as it is not manufactured for use in the United States. Read More...
Jbb March 02, 2015 for Model Number WM2016CW If the washer water level pressure switch (LG part number AP5078539 your number 6601CR1006A) is no longer available, what do I use instead? You offer no alternative on your website.
Djs January 08, 2015 for Model Number WM2487HRMA LG washer is about 6 years old. Last few weeks flashed dE error when starting wash which is a door error even though the door is closed tightly. If power off and close door again and retry will work after 4-6 attempts.
1 Answer Hello DJS. You will need to order and replace the door lock assembly on the unit. Read More...
Jc December 15, 2014 for Model Number WM3988HWA My LG is a washer dryer combo. When I put it on a regular cycle it will wash and drain properly all the way up to the time it is supposed to go into the dry mode. when the "drying" mode comes on , water comes into the drum...the clothes are soaked again.Help! I need to know if the repair would be a reasonable amount or if I should just get a new washer..the unit is 6 years old. Thank you for any advice you can give me!
1 Answer JC, With the unit going from spin and then filling when it is supposed to go to the dry cycle would most likely be caused by a faulty control board. Read More...