Dave June 16, 2018 for Model Number Samsung fridge Rf263beaesr/aa A few weeks back the fridge died completely. I replaced the Main PCB and the inverter board. Everything works except the ice maker. Any ideas?
1 Answer Dave, Check the CN90 connector on the new control board, make sure there are no loose or damaged wires and the connection is good and tight. Check the ice cube tray, make sure it is in the horizontal position then press the test switch on the side of the I/M control, and see if the ice maker operates, Then listen for the water valve to activate when the tray returns to the horizontal Read More...
Dave May 25, 2018 for Model Number RF263BEAEBC Just replaced the original ice maker DA97-12317A, with recommended replacement DA97-15217D. The old one made ice but would only dump if the reset button was pushed. The new one won’t do anything, no ice, reset seems non- responsive. Now what?
1 Answer Hello Dave, If the new icemaker will not work and the connections are the same and tight, you could have a bad water valve or the new icemaker DA97-15217D is defective. Read More...
Dallas May 15, 2018 for Model Number RF263BEAESR/AA 06 Is this the correct part# for the top icemaker assy?
Lori April 06, 2018 Our Samsung refigerator is about 18 months old. We have had many different problems with our top icemaker. Making too much ice, icing up, leaking water from from and into bottom of fridge. Recently started only making ice when reset was pushed. I have force defrosted the freezer, nothing helps. Now, I push the reset button and it makes the reset sound, but nothing happens, it does absolutely nothing. Also, our bucket where all the ice would dump, if it worked still, is cracked. Any suggestions on where to start? I see suggestions for board and assembly. The parts look pricey, is there a replace whole icemaker option, that would be cheaper than replacing the individual parts?(board, assembly, icebucket?)
1 Answer Lori, For the ice bucket it would need to be replaced if it is cracked. For the issue going on with the icemaker it would be a icemaker that is faulty. Read More...
Barry February 19, 2018 for Model Number RF28HFEDBSR/AA-0000 My icemaker is set at -2 and is leaking due to a buildup of ice in the "ice room". I am able to break down the ice and reset the icemaker, but within a couple weeks the build up is back. Is this likely an issue with the icemaker assembly or another part? Thanks in advance!
1 Answer Barry, It would be likely that the icemaker is the issue but will want to check to make sure that the water valve is not seeping causing the unit to overfill. Read More...
Paul G. January 05, 2018 for Model Number DA97-15217A-00 Ice Maker The ice maker itself must have overflowed and the bottom of the ice maker is covered with ice. I got the container out but now how do I defrost the ice maker?
1 Answer Hello Paul, You can use a hair dryer to defrost the icemaker. The problem was likely caused by a bad water valve. I'm sorry but we will need to ask you to post a new question including the model number from your units' I.D. tag so we can recommend parts that can be guaranteed to work properly on your unit. Thank you for your patience and understanding in this matter. Read More...
Seth December 29, 2017 for Model Number RF28HFEDBSR/AA I have a Samsung Refrigerator with the follow parts/Model Numbers: Refrigerator Model Number - RF28HFEDBSR/AA (Manu APR 2016) Ice Maker Model Number - DA97-15217A-00 Ice Auger Assembly - DA97-12540A Of course I’m just over the year warranty and I am having the following problem: Ice Production Does not stop automatically resulting in over production of ice and jamming of ice in the Ice Maker. Questions for you: - How does this ice Maker determine enough ice has been produced? Through a sensor on the ice Maker? I cannot seem to locate any mechanical switches. - What replacement options are available to remedy this ongoing issue?
1 Answer Seth, There is an arm on the side of the icemaker that drops down to sense the ice level. If the arm is broken off or the sensor inside the icemaker does not sense ice level it will continue to make ice. For this issue the icemaker would need to be replaced. Read More...
Roy December 07, 2017 for Model Number Rf28hmedbsr/aa The answer to my previous question talked about temperature, the temp is -2 and 36, temp isn't the problem, it's cold enough, makes ice quick, just won't dump unless reset is pushed. Evidently it's the board do you stock it and what is the part number? Thanks
Roy December 06, 2017 for Model Number rf28hmedbsr/aa Ice maker would only make ice when reset pushed then would cycle once you guys suggested replacing ice maker which I did still same problem I read above it wouldn't cycle at all if board was faulty is that true or not if so what else could cause this seems to be a common problem with no clear answer help please
1 Answer Hello Roy. Yes, that can be the case. However, most issues like these are caused by the temp not being 0-5° in the icemaker. You will need to check that first before replacing the board. Read More...
Tom November 06, 2017 for Model Number AP6261445 I’ve seen your comments that the ice maker temp needs to be 0-5 degrees. I assume that’s Fahrenheit? My ice maker will drop a tray of ice every 24 hours or so and the temp inside seems to be around 15 degrees. Any suggestions?
1 Answer Hello Tom. The reason for slow ice production is the temp. It has to be 0-5° for the unit to cycle every 2-3 hours. If 15, it takes longer to full freezer and is the reason for long cycle time. Thanks. Read More...