Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Range Main Control Board by Samsung

Best Seller
Manufacturer Part
4.89 (64)
By: Samsung
Part Number: OEM16959930
Manufacturer Part Number: DE92-02588C

Fix error codes SE, E-0E, or unresponsive controls with a new main control board. Straightforward DIY repair—disconnect old connectors, reconnect new board.

More
$247.95

Out Of Stock

Usually ships within 4 - 14 days

Add to Cart

Questions & Answers

For Samsung Range Main Control Board (Part Number: OEM16959930)

Brian for Model Number NX58H5600SS/AA -but not sure if it is 00, 01, 02

I attempted to replace parts with no luck for my Samsung Convection gas range manufactured in august 2015; the model # is NX58H5600SS/AA it appears there are variations on the same model, and I am trying to figure out if it is a NX58H5600SS/AA "00", "01" or "02" . I ordered a new touchpad DG34-00027B which worked for 3 weeks or so and then started with error code SE. I then ordered a new control board, and it will work for about 6 hours before beeping and reverting to SE code. I am being told the new touchpad may be a dud, but after further research, I am wondering if I needed part # DG34-00027D instead. the serial number is 0BGG7DDG801800T. Is there a way to use the serial # to determine what exact model variation my range is? thanks!

1 Answer

Brian,

There should be a revision number on your model tag. If there is no revision number then go with the 00 on the end. This issue would be in the touchpad.

Read More...
Brian for Model Number Samsung Gas Oven RangeNX58H5600SS

I have a 2015 Samsung Gas Oven RangeNX58H5600SS that was having problems with the touchpad (some buttons no longer functioned); I replaced the pad with a Superunner Membrane Switch Touchpad DG34-00027B. It worked for about 3 weeks, and then I started getting error code SE with beeps. I attempted some resets, made sure touchpad was installed correctly with no luck. The touchpad may have gotten wet, but appears sealed from moisture...I then bought and installed a Range Oven Control Board DE92-02588J. It now works for about 6 hours then starts the SE code again. I have tried many resets; self cleaning, etc. with no luck. Is there a way to tell where the short is? I have a multimeter, but not enough info about what to test and how. My suspicion is the replacement touchpad was bad-but is there a way to test it rather than buy another? Please help-I am very frustrated and my wife is stockpiling way too much "I told you you couldn't fix it" argument ammo...

1 Answer

Brian, the main control connection CN301 can be tested for a short between the pins on the connector. If there is a short, the main control DE92-02588J has failed. If there is not a shorted pin set, then the touchpad DG34-00027B is faulty.

Read More...

1 Answer

Hello Paul,
the new bake igniter should have lasted years. If it has the same problem as before , meaning it is glowing but the gas valve is not opening, test that the stove is getting 120vac in bake mode, if it is lower,say 110v that may be a problem as the igniter is rated for 120v to be able to draw 3.5 amps to open the gas valve. If that is not the problem check the bake burner tube DG62-00066A the glow igniter DG94-00520A, should be positioned parallel to the burner tube and the ports on the tube should not be corroded, the air shutter should be wide open (LP setting), because if the burner does not burn cleanly there can be a residue build-up on the igniter that will shorten its life.

Read More...

1 Answer

Hello Richard. 1. Check if cable of keypad has been inserted into connector of
main PCB.
2. Check for short between main PCB and connector or keypad
and cable.
3. If there is not a problem with connector on main PCB and cable
of keypad, replace the main PCB.

Read More...

1 Answer

Hello Abe. Yes, it is that simple. They say that in case something gets shorted out or to make sure they are not hooked up wrong. You should be able to do it yourself.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google