Rick September 21, 2019 for Model Number WA48H7400AW/A2 Where is the mems sensor located on Samsung washer WA48H7400AW/A2? Thanks, Rick
1 Answer Rick, It appears that the mems sensor will go at the bottom of the outer tub. If you lay the unit on its back or side you should see the sensor. Read More...
Md August 20, 2019 for Model Number WF56H9100AG/A2-0000 Once I press start, the washer goes through its normal sequence of test it usually does, then the door locks and after like 15 seconds the door unlock and nothing happens. I get the 8E error code when going through the diagnostic. Any good place to start to troubleshoot this machine?
1 Answer Hello MD, you'll want to check the connections going to the main board if all look good you might have to replace board. Thanks! Read More...
Ron August 17, 2019 for Model Number wa48h7400aw/a2 I check for errors and got a 8e code but why don't I get a code when I run it with out clothes in it, it run through all cycles perfect empty, its say mems sensor but how can that be bad when everything works when you run it with no clothes in it?
1 Answer Ron, this is going to indicate that there is a voltage output error with the MEMS sensor DC93-00278B which will occur if the sensor registers excess vibrations which can occur when loaded. The MEMS sensor can be tested at the sub-control interface DC92-01624A at connection 15P which is a 6 wire connector. The voltage output should read more than 0.5V and less than 4.5V with the black probe of a multimeter on the blue wire at pin 5 and testing pins 2, 3, 4, and 6. Pin 1 red wire should read 3.3V DC when tested to pin 5 blue wire. The unit will need to be in operation when performing this testing procedure so caution will need to be used. If the voltages read within the tolerances, then the issue would be with the control. If the voltages are outside of the tolerances, the issue would be with the MEMS sensor unless pin 1 is not reading 3.3V, this would be a control failure. Read More...
Ron August 10, 2019 for Model Number wa48h7400aw/a2 The washer works perfect when empty, goes all the way through the cycles, But with clothes in it, it fills then beeps and pumps back out
1 Answer Ron, For this issue, it would be recommended to check to see if there are any stored error codes by putting the unit into diagnostics. This will be the best option because if there are any error codes it will point you to what may be faulty. Read More...
Kim July 25, 2019 for Model Number WA50K8600AV/AA I originally got an error code for the mems sensor. Replacement of the sensor didn’t fix the issue so I replaced the control board. New error code pointed to the hall sensor and after replacement I get amother mems sensor code. Any suggestions. The washer is less than 2 yrs old.
1 Answer Kim, What is the error code in the display? in the meantime, disconnect and check the mems sensor wire harness and connections at both the sensor and the main control board. Make sure there's no corrosion, rust or debris on the pins of the harness connectors. Make sure the washer is level in both directions and the tub moves freely in all directions when you manually move the tub. Make sure the washer sits "solid" on the floor and the floor is "solid" enough to support the washer with a load of clothes in the spin cycle. Read More...
Sean July 20, 2019 for Model Number WA52M7750AV/A4 My washer (WA52M7750AV/A4) is throwing an 8E error code. I replaced the MEMS sensor and control panel (genuine Samsung parts). It continues to throw the error code. What else could it be? Wiring? Dampening rods?
1 Answer Sean, based on the information provided, along with the main control DC92-02005A and MEMS sensor DC93-00278B having been replaced, the most likely issue would be with the wiring harness DC93-00665A itself. If it were to throw an out of balance error, then it could be the dampening rods DC97-18610F, but as it is just indicating the MEMS sensor failing, the dampening rods would not be likely. Read More...
Cj July 15, 2019 for Model Number WF435ATGJRA/A1-0001 Where is the mems sensor located on a Samsung Wf435atgjra/a1? I am getting an 8e error code
1 Answer CJ, When you open the main top of the unit there will be a metal bar that runs across. The Mems Sensor will be located on this metal bar underneath it. Read More...
Charode June 24, 2019 for Model Number WF45H6300AW/A2 I received an error code 8E on the screen. My smart care shows it as a mems sensor. However when I tilted it it acted like it wanted to work. I placed a level on it and noticed that it was not balanced left to right. Will that cause the error or should I just by a sensor?
1 Answer Charode, the unit not being balanced can cause this issue. Once the unit is level, you may want to test the wash cycle for operation. If it does not operate properly or gives the error again, from there you would want to check the wiring connections at the mems sensor [DC93-00278D] and the control. If those check good, then you would want to replace the sensor. Read More...
Danielle June 09, 2019 for Model Number Wf45h6300ag/a2 Hi. Where is the mems sensor located in this model washer
1 Answer Daniel, the mems sensor DC93-00278D for your model is going to be located on the top of the tub assembly towards the back. Read More...
Kim June 07, 2019 for Model Number WA50K8600AV/AA I'm trying to locate a part number for the mems sensor. Thanks